Filtered by vendor Linux
Subscribe
Total
19806 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2025-39875 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: igb: Fix NULL pointer dereference in ethtool loopback test The igb driver currently causes a NULL pointer dereference when executing the ethtool loopback test. This occurs because there is no associated q_vector for the test ring when it is set up, as interrupts are typically not added to the test rings. Since commit 5ef44b3cb43b removed the napi_id assignment in __xdp_rxq_info_reg(), there is no longer a need to pass a napi_id to it. Therefore, simply use 0 as the last parameter. | |||||
| CVE-2025-39928 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: i2c: rtl9300: ensure data length is within supported range Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer' to ensure the data length isn't within the supported range. In particular a data length of 0 is not supported by the hardware and causes unintended or destructive behaviour. This limitation becomes obvious when looking at the register documentation [1]. 4 bits are reserved for DATA_WIDTH and the value of these 4 bits is used as N + 1, allowing a data length range of 1 <= len <= 16. Affected by this is the SMBus Quick Operation which works with a data length of 0. Passing 0 as the length causes an underflow of the value due to: (len - 1) & 0xf and effectively specifying a transfer length of 16 via the registers. This causes a 16-byte write operation instead of a Quick Write. For example, on SFP modules without write-protected EEPROM this soft-bricks them by overwriting some initial bytes. For completeness, also add a quirk for the zero length. [1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2 | |||||
| CVE-2025-39903 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: of_numa: fix uninitialized memory nodes causing kernel panic When there are memory-only nodes (nodes without CPUs), these nodes are not properly initialized, causing kernel panic during boot. of_numa_init of_numa_parse_cpu_nodes node_set(nid, numa_nodes_parsed); of_numa_parse_memory_nodes In of_numa_parse_cpu_nodes, numa_nodes_parsed gets updated only for nodes containing CPUs. Memory-only nodes should have been updated in of_numa_parse_memory_nodes, but they weren't. Subsequently, when free_area_init() attempts to access NODE_DATA() for these uninitialized memory nodes, the kernel panics due to NULL pointer dereference. This can be reproduced on ARM64 QEMU with 1 CPU and 2 memory nodes: qemu-system-aarch64 \ -cpu host -nographic \ -m 4G -smp 1 \ -machine virt,accel=kvm,gic-version=3,iommu=smmuv3 \ -object memory-backend-ram,size=2G,id=mem0 \ -object memory-backend-ram,size=2G,id=mem1 \ -numa node,nodeid=0,memdev=mem0 \ -numa node,nodeid=1,memdev=mem1 \ -kernel $IMAGE \ -hda $DISK \ -append "console=ttyAMA0 root=/dev/vda rw earlycon" [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x481fd010] [ 0.000000] Linux version 6.17.0-rc1-00001-gabb4b3daf18c-dirty (yintirui@local) (gcc (GCC) 12.3.1, GNU ld (GNU Binutils) 2.41) #52 SMP PREEMPT Mon Aug 18 09:49:40 CST 2025 [ 0.000000] KASLR enabled [ 0.000000] random: crng init done [ 0.000000] Machine model: linux,dummy-virt [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: pl11 at MMIO 0x0000000009000000 (options '') [ 0.000000] printk: legacy bootconsole [pl11] enabled [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] NODE_DATA(0) allocated [mem 0xbfffd9c0-0xbfffffff] [ 0.000000] node 1 must be removed before remove section 23 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] node 1: [mem 0x00000000c0000000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a0 [ 0.000000] Mem abort info: [ 0.000000] ESR = 0x0000000096000004 [ 0.000000] EC = 0x25: DABT (current EL), IL = 32 bits [ 0.000000] SET = 0, FnV = 0 [ 0.000000] EA = 0, S1PTW = 0 [ 0.000000] FSC = 0x04: level 0 translation fault [ 0.000000] Data abort info: [ 0.000000] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 0.000000] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 0.000000] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 0.000000] [00000000000000a0] user address but active_mm is swapper [ 0.000000] Internal error: Oops: 0000000096000004 [#1] SMP [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 UID: 0 PID: 0 Comm: swapper Not tainted 6.17.0-rc1-00001-g760c6dabf762-dirty #54 PREEMPT [ 0.000000] Hardware name: linux,dummy-virt (DT) [ 0.000000] pstate: 800000c5 (Nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 0.000000] pc : free_area_init+0x50c/0xf9c [ 0.000000] lr : free_area_init+0x5c0/0xf9c [ 0.000000] sp : ffffa02ca0f33c00 [ 0.000000] x29: ffffa02ca0f33cb0 x28: 0000000000000000 x27: 0000000000000000 [ 0.000000] x26: 4ec4ec4ec4ec4ec5 x25: 00000000000c0000 x24: 00000000000c0000 [ 0.000000] x23: 0000000000040000 x22: 0000000000000000 x21: ffffa02ca0f3b368 [ 0.000000] x20: ffffa02ca14c7b98 x19: 0000000000000000 x18: 0000000000000002 [ 0.000000] x17: 000000000000cacc x16: 0000000000000001 x15: 0000000000000001 [ 0.000000] x14: 0000000080000000 x13: 0000000000000018 x12: 0000000000000002 [ 0.0 ---truncated--- | |||||
| CVE-2025-39876 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: fec: Fix possible NPD in fec_enet_phy_reset_after_clk_enable() The function of_phy_find_device may return NULL, so we need to take care before dereferencing phy_dev. | |||||
| CVE-2025-38682 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: i2c: core: Fix double-free of fwnode in i2c_unregister_device() Before commit df6d7277e552 ("i2c: core: Do not dereference fwnode in struct device"), i2c_unregister_device() only called fwnode_handle_put() on of_node-s in the form of calling of_node_put(client->dev.of_node). But after this commit the i2c_client's fwnode now unconditionally gets fwnode_handle_put() on it. When the i2c_client has no primary (ACPI / OF) fwnode but it does have a software fwnode, the software-node will be the primary node and fwnode_handle_put() will put() it. But for the software fwnode device_remove_software_node() will also put() it leading to a double free: [ 82.665598] ------------[ cut here ]------------ [ 82.665609] refcount_t: underflow; use-after-free. [ 82.665808] WARNING: CPU: 3 PID: 1502 at lib/refcount.c:28 refcount_warn_saturate+0xba/0x11 ... [ 82.666830] RIP: 0010:refcount_warn_saturate+0xba/0x110 ... [ 82.666962] <TASK> [ 82.666971] i2c_unregister_device+0x60/0x90 Fix this by not calling fwnode_handle_put() when the primary fwnode is a software-node. | |||||
| CVE-2025-39885 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix recursive semaphore deadlock in fiemap call syzbot detected a OCFS2 hang due to a recursive semaphore on a FS_IOC_FIEMAP of the extent list on a specially crafted mmap file. context_switch kernel/sched/core.c:5357 [inline] __schedule+0x1798/0x4cc0 kernel/sched/core.c:6961 __schedule_loop kernel/sched/core.c:7043 [inline] schedule+0x165/0x360 kernel/sched/core.c:7058 schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:7115 rwsem_down_write_slowpath+0x872/0xfe0 kernel/locking/rwsem.c:1185 __down_write_common kernel/locking/rwsem.c:1317 [inline] __down_write kernel/locking/rwsem.c:1326 [inline] down_write+0x1ab/0x1f0 kernel/locking/rwsem.c:1591 ocfs2_page_mkwrite+0x2ff/0xc40 fs/ocfs2/mmap.c:142 do_page_mkwrite+0x14d/0x310 mm/memory.c:3361 wp_page_shared mm/memory.c:3762 [inline] do_wp_page+0x268d/0x5800 mm/memory.c:3981 handle_pte_fault mm/memory.c:6068 [inline] __handle_mm_fault+0x1033/0x5440 mm/memory.c:6195 handle_mm_fault+0x40a/0x8e0 mm/memory.c:6364 do_user_addr_fault+0x764/0x1390 arch/x86/mm/fault.c:1387 handle_page_fault arch/x86/mm/fault.c:1476 [inline] exc_page_fault+0x76/0xf0 arch/x86/mm/fault.c:1532 asm_exc_page_fault+0x26/0x30 arch/x86/include/asm/idtentry.h:623 RIP: 0010:copy_user_generic arch/x86/include/asm/uaccess_64.h:126 [inline] RIP: 0010:raw_copy_to_user arch/x86/include/asm/uaccess_64.h:147 [inline] RIP: 0010:_inline_copy_to_user include/linux/uaccess.h:197 [inline] RIP: 0010:_copy_to_user+0x85/0xb0 lib/usercopy.c:26 Code: e8 00 bc f7 fc 4d 39 fc 72 3d 4d 39 ec 77 38 e8 91 b9 f7 fc 4c 89 f7 89 de e8 47 25 5b fd 0f 01 cb 4c 89 ff 48 89 d9 4c 89 f6 <f3> a4 0f 1f 00 48 89 cb 0f 01 ca 48 89 d8 5b 41 5c 41 5d 41 5e 41 RSP: 0018:ffffc9000403f950 EFLAGS: 00050256 RAX: ffffffff84c7f101 RBX: 0000000000000038 RCX: 0000000000000038 RDX: 0000000000000000 RSI: ffffc9000403f9e0 RDI: 0000200000000060 RBP: ffffc9000403fa90 R08: ffffc9000403fa17 R09: 1ffff92000807f42 R10: dffffc0000000000 R11: fffff52000807f43 R12: 0000200000000098 R13: 00007ffffffff000 R14: ffffc9000403f9e0 R15: 0000200000000060 copy_to_user include/linux/uaccess.h:225 [inline] fiemap_fill_next_extent+0x1c0/0x390 fs/ioctl.c:145 ocfs2_fiemap+0x888/0xc90 fs/ocfs2/extent_map.c:806 ioctl_fiemap fs/ioctl.c:220 [inline] do_vfs_ioctl+0x1173/0x1430 fs/ioctl.c:532 __do_sys_ioctl fs/ioctl.c:596 [inline] __se_sys_ioctl+0x82/0x170 fs/ioctl.c:584 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f5f13850fd9 RSP: 002b:00007ffe3b3518b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000200000000000 RCX: 00007f5f13850fd9 RDX: 0000200000000040 RSI: 00000000c020660b RDI: 0000000000000004 RBP: 6165627472616568 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffe3b3518f0 R13: 00007ffe3b351b18 R14: 431bde82d7b634db R15: 00007f5f1389a03b ocfs2_fiemap() takes a read lock of the ip_alloc_sem semaphore (since v2.6.22-527-g7307de80510a) and calls fiemap_fill_next_extent() to read the extent list of this running mmap executable. The user supplied buffer to hold the fiemap information page faults calling ocfs2_page_mkwrite() which will take a write lock (since v2.6.27-38-g00dc417fa3e7) of the same semaphore. This recursive semaphore will hold filesystem locks and causes a hang of the fileystem. The ip_alloc_sem protects the inode extent list and size. Release the read semphore before calling fiemap_fill_next_extent() in ocfs2_fiemap() and ocfs2_fiemap_inline(). This does an unnecessary semaphore lock/unlock on the last extent but simplifies the error path. | |||||
| CVE-2025-39888 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: fuse: Block access to folio overlimit syz reported a slab-out-of-bounds Write in fuse_dev_do_write. When the number of bytes to be retrieved is truncated to the upper limit by fc->max_pages and there is an offset, the oob is triggered. Add a loop termination condition to prevent overruns. | |||||
| CVE-2025-39918 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: fix linked list corruption Never leave scheduled wcid entries on the temporary on-stack list | |||||
| CVE-2025-39887 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: tracing/osnoise: Fix null-ptr-deref in bitmap_parselist() A crash was observed with the following output: BUG: kernel NULL pointer dereference, address: 0000000000000010 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 2 UID: 0 PID: 92 Comm: osnoise_cpus Not tainted 6.17.0-rc4-00201-gd69eb204c255 #138 PREEMPT(voluntary) RIP: 0010:bitmap_parselist+0x53/0x3e0 Call Trace: <TASK> osnoise_cpus_write+0x7a/0x190 vfs_write+0xf8/0x410 ? do_sys_openat2+0x88/0xd0 ksys_write+0x60/0xd0 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> This issue can be reproduced by below code: fd=open("/sys/kernel/debug/tracing/osnoise/cpus", O_WRONLY); write(fd, "0-2", 0); When user pass 'count=0' to osnoise_cpus_write(), kmalloc() will return ZERO_SIZE_PTR (16) and cpulist_parse() treat it as a normal value, which trigger the null pointer dereference. Add check for the parameter 'count'. | |||||
| CVE-2025-39675 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add null pointer check in mod_hdcp_hdcp1_create_session() The function mod_hdcp_hdcp1_create_session() calls the function get_first_active_display(), but does not check its return value. The return value is a null pointer if the display list is empty. This will lead to a null pointer dereference. Add a null pointer check for get_first_active_display() and return MOD_HDCP_STATUS_DISPLAY_NOT_FOUND if the function return null. This is similar to the commit c3e9826a2202 ("drm/amd/display: Add null pointer check for get_first_active_display()"). (cherry picked from commit 5e43eb3cd731649c4f8b9134f857be62a416c893) | |||||
| CVE-2025-39715 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: parisc: Revise gateway LWS calls to probe user read access We use load and stbys,e instructions to trigger memory reference interruptions without writing to memory. Because of the way read access support is implemented, read access interruptions are only triggered at privilege levels 2 and 3. The kernel and gateway page execute at privilege level 0, so this code never triggers a read access interruption. Thus, it is currently possible for user code to execute a LWS compare and swap operation at an address that is read protected at privilege level 3 (PRIV_USER). Fix this by probing read access rights at privilege level 3 and branching to lws_fault if access isn't allowed. | |||||
| CVE-2025-39787 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: soc: qcom: mdt_loader: Ensure we don't read past the ELF header When the MDT loader is used in remoteproc, the ELF header is sanitized beforehand, but that's not necessary the case for other clients. Validate the size of the firmware buffer to ensure that we don't read past the end as we iterate over the header. e_phentsize and e_shentsize are validated as well, to ensure that the assumptions about step size in the traversal are valid. | |||||
| CVE-2025-68333 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix possible deadlock in the deferred_irq_workfn() For PREEMPT_RT=y kernels, the deferred_irq_workfn() is executed in the per-cpu irq_work/* task context and not disable-irq, if the rq returned by container_of() is current CPU's rq, the following scenarios may occur: lock(&rq->__lock); <Interrupt> lock(&rq->__lock); This commit use IRQ_WORK_INIT_HARD() to replace init_irq_work() to initialize rq->scx.deferred_irq_work, make the deferred_irq_workfn() is always invoked in hard-irq context. | |||||
| CVE-2025-39687 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: iio: light: as73211: Ensure buffer holes are zeroed Given that the buffer is copied to a kfifo that ultimately user space can read, ensure we zero it. | |||||
| CVE-2025-39694 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 7.3 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: s390/sclp: Fix SCCB present check Tracing code called by the SCLP interrupt handler contains early exits if the SCCB address associated with an interrupt is NULL. This check is performed after physical to virtual address translation. If the kernel identity mapping does not start at address zero, the resulting virtual address is never zero, so that the NULL checks won't work. Subsequently this may result in incorrect accesses to the first page of the identity mapping. Fix this by introducing a function that handles the NULL case before address translation. | |||||
| CVE-2025-38735 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: gve: prevent ethtool ops after shutdown A crash can occur if an ethtool operation is invoked after shutdown() is called. shutdown() is invoked during system shutdown to stop DMA operations without performing expensive deallocations. It is discouraged to unregister the netdev in this path, so the device may still be visible to userspace and kernel helpers. In gve, shutdown() tears down most internal data structures. If an ethtool operation is dispatched after shutdown(), it will dereference freed or NULL pointers, leading to a kernel panic. While graceful shutdown normally quiesces userspace before invoking the reboot syscall, forced shutdowns (as observed on GCP VMs) can still trigger this path. Fix by calling netif_device_detach() in shutdown(). This marks the device as detached so the ethtool ioctl handler will skip dispatching operations to the driver. | |||||
| CVE-2025-39926 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: genetlink: fix genl_bind() invoking bind() after -EPERM Per family bind/unbind callbacks were introduced to allow families to track multicast group consumer presence, e.g. to start or stop producing events depending on listeners. However, in genl_bind() the bind() callback was invoked even if capability checks failed and ret was set to -EPERM. This means that callbacks could run on behalf of unauthorized callers while the syscall still returned failure to user space. Fix this by only invoking bind() after "if (ret) break;" check i.e. after permission checks have succeeded. | |||||
| CVE-2025-39934 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm: bridge: anx7625: Fix NULL pointer dereference with early IRQ If the interrupt occurs before resource initialization is complete, the interrupt handler/worker may access uninitialized data such as the I2C tcpc_client device, potentially leading to NULL pointer dereference. | |||||
| CVE-2025-38714 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: hfsplus: fix slab-out-of-bounds in hfsplus_bnode_read() The hfsplus_bnode_read() method can trigger the issue: [ 174.852007][ T9784] ================================================================== [ 174.852709][ T9784] BUG: KASAN: slab-out-of-bounds in hfsplus_bnode_read+0x2f4/0x360 [ 174.853412][ T9784] Read of size 8 at addr ffff88810b5fc6c0 by task repro/9784 [ 174.854059][ T9784] [ 174.854272][ T9784] CPU: 1 UID: 0 PID: 9784 Comm: repro Not tainted 6.16.0-rc3 #7 PREEMPT(full) [ 174.854281][ T9784] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 174.854286][ T9784] Call Trace: [ 174.854289][ T9784] <TASK> [ 174.854292][ T9784] dump_stack_lvl+0x10e/0x1f0 [ 174.854305][ T9784] print_report+0xd0/0x660 [ 174.854315][ T9784] ? __virt_addr_valid+0x81/0x610 [ 174.854323][ T9784] ? __phys_addr+0xe8/0x180 [ 174.854330][ T9784] ? hfsplus_bnode_read+0x2f4/0x360 [ 174.854337][ T9784] kasan_report+0xc6/0x100 [ 174.854346][ T9784] ? hfsplus_bnode_read+0x2f4/0x360 [ 174.854354][ T9784] hfsplus_bnode_read+0x2f4/0x360 [ 174.854362][ T9784] hfsplus_bnode_dump+0x2ec/0x380 [ 174.854370][ T9784] ? __pfx_hfsplus_bnode_dump+0x10/0x10 [ 174.854377][ T9784] ? hfsplus_bnode_write_u16+0x83/0xb0 [ 174.854385][ T9784] ? srcu_gp_start+0xd0/0x310 [ 174.854393][ T9784] ? __mark_inode_dirty+0x29e/0xe40 [ 174.854402][ T9784] hfsplus_brec_remove+0x3d2/0x4e0 [ 174.854411][ T9784] __hfsplus_delete_attr+0x290/0x3a0 [ 174.854419][ T9784] ? __pfx_hfs_find_1st_rec_by_cnid+0x10/0x10 [ 174.854427][ T9784] ? __pfx___hfsplus_delete_attr+0x10/0x10 [ 174.854436][ T9784] ? __asan_memset+0x23/0x50 [ 174.854450][ T9784] hfsplus_delete_all_attrs+0x262/0x320 [ 174.854459][ T9784] ? __pfx_hfsplus_delete_all_attrs+0x10/0x10 [ 174.854469][ T9784] ? rcu_is_watching+0x12/0xc0 [ 174.854476][ T9784] ? __mark_inode_dirty+0x29e/0xe40 [ 174.854483][ T9784] hfsplus_delete_cat+0x845/0xde0 [ 174.854493][ T9784] ? __pfx_hfsplus_delete_cat+0x10/0x10 [ 174.854507][ T9784] hfsplus_unlink+0x1ca/0x7c0 [ 174.854516][ T9784] ? __pfx_hfsplus_unlink+0x10/0x10 [ 174.854525][ T9784] ? down_write+0x148/0x200 [ 174.854532][ T9784] ? __pfx_down_write+0x10/0x10 [ 174.854540][ T9784] vfs_unlink+0x2fe/0x9b0 [ 174.854549][ T9784] do_unlinkat+0x490/0x670 [ 174.854557][ T9784] ? __pfx_do_unlinkat+0x10/0x10 [ 174.854565][ T9784] ? __might_fault+0xbc/0x130 [ 174.854576][ T9784] ? getname_flags.part.0+0x1c5/0x550 [ 174.854584][ T9784] __x64_sys_unlink+0xc5/0x110 [ 174.854592][ T9784] do_syscall_64+0xc9/0x480 [ 174.854600][ T9784] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 174.854608][ T9784] RIP: 0033:0x7f6fdf4c3167 [ 174.854614][ T9784] Code: f0 ff ff 73 01 c3 48 8b 0d 26 0d 0e 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 08 [ 174.854622][ T9784] RSP: 002b:00007ffcb948bca8 EFLAGS: 00000206 ORIG_RAX: 0000000000000057 [ 174.854630][ T9784] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f6fdf4c3167 [ 174.854636][ T9784] RDX: 00007ffcb948bcc0 RSI: 00007ffcb948bcc0 RDI: 00007ffcb948bd50 [ 174.854641][ T9784] RBP: 00007ffcb948cd90 R08: 0000000000000001 R09: 00007ffcb948bb40 [ 174.854645][ T9784] R10: 00007f6fdf564fc0 R11: 0000000000000206 R12: 0000561e1bc9c2d0 [ 174.854650][ T9784] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 174.854658][ T9784] </TASK> [ 174.854661][ T9784] [ 174.879281][ T9784] Allocated by task 9784: [ 174.879664][ T9784] kasan_save_stack+0x20/0x40 [ 174.880082][ T9784] kasan_save_track+0x14/0x30 [ 174.880500][ T9784] __kasan_kmalloc+0xaa/0xb0 [ 174.880908][ T9784] __kmalloc_noprof+0x205/0x550 [ 174.881337][ T9784] __hfs_bnode_create+0x107/0x890 [ 174.881779][ T9784] hfsplus_bnode_find+0x2d0/0xd10 [ 174.882222][ T9784] hfsplus_brec_find+0x2b0/0x520 [ 174.882659][ T9784] hfsplus_delete_all_attrs+0x23b/0x3 ---truncated--- | |||||
| CVE-2025-39742 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-19 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: RDMA: hfi1: fix possible divide-by-zero in find_hw_thread_mask() The function divides number of online CPUs by num_core_siblings, and later checks the divider by zero. This implies a possibility to get and divide-by-zero runtime error. Fix it by moving the check prior to division. This also helps to save one indentation level. | |||||