Total
19304 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2026-31751 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 4.7 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: comedi: dt2815: add hardware detection to prevent crash The dt2815 driver crashes when attached to I/O ports without actual hardware present. This occurs because syzkaller or users can attach the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl. When no hardware exists at the specified port, inb() operations return 0xff (floating bus), but outb() operations can trigger page faults due to undefined behavior, especially under race conditions: BUG: unable to handle page fault for address: 000000007fffff90 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page RIP: 0010:dt2815_attach+0x6e0/0x1110 Add hardware detection by reading the status register before attempting any write operations. If the read returns 0xff, assume no hardware is present and fail the attach with -ENODEV. This prevents crashes from outb() operations on non-existent hardware. | |||||
| CVE-2026-31750 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: comedi: runflags cannot determine whether to reclaim chanlist syzbot reported a memory leak [1], because commit 4e1da516debb ("comedi: Add reference counting for Comedi command handling") did not consider the exceptional exit case in do_cmd_ioctl() where runflags is not set. This caused chanlist not to be properly freed by do_become_nonbusy(), as it only frees chanlist when runflags is correctly set. Added a check in do_become_nonbusy() for the case where runflags is not set, to properly free the chanlist memory. [1] BUG: memory leak backtrace (crc 844a0efa): __comedi_get_user_chanlist drivers/comedi/comedi_fops.c:1815 [inline] do_cmd_ioctl.part.0+0x112/0x350 drivers/comedi/comedi_fops.c:1890 do_cmd_ioctl drivers/comedi/comedi_fops.c:1858 [inline] | |||||
| CVE-2026-31749 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: comedi: ni_atmio16d: Fix invalid clean-up after failed attach If the driver's COMEDI "attach" handler function (`atmio16d_attach()`) returns an error, the COMEDI core will call the driver's "detach" handler function (`atmio16d_detach()`) to clean up. This calls `reset_atmio16d()` unconditionally, but depending on where the error occurred in the attach handler, the device may not have been sufficiently initialized to call `reset_atmio16d()`. It uses `dev->iobase` as the I/O port base address and `dev->private` as the pointer to the COMEDI device's private data structure. `dev->iobase` may still be set to its initial value of 0, which would result in undesired writes to low I/O port addresses. `dev->private` may still be `NULL`, which would result in null pointer dereferences. Fix `atmio16d_detach()` by checking that `dev->private` is valid (non-null) before calling `reset_atmio16d()`. This implies that `dev->iobase` was set correctly since that is set up before `dev->private`. | |||||
| CVE-2026-31748 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: comedi: me_daq: Fix potential overrun of firmware buffer `me2600_xilinx_download()` loads the firmware that was requested by `request_firmware()`. It is possible for it to overrun the source buffer because it blindly trusts the file format. It reads a data stream length from the first 4 bytes into variable `file_length` and reads the data stream contents of length `file_length` from offset 16 onwards. Although it checks that the supplied firmware is at least 16 bytes long, it does not check that it is long enough to contain the data stream. Add a test to ensure that the supplied firmware is long enough to contain the header and the data stream. On failure, log an error and return `-EINVAL`. | |||||
| CVE-2026-31747 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: comedi: me4000: Fix potential overrun of firmware buffer `me4000_xilinx_download()` loads the firmware that was requested by `request_firmware()`. It is possible for it to overrun the source buffer because it blindly trusts the file format. It reads a data stream length from the first 4 bytes into variable `file_length` and reads the data stream contents of length `file_length` from offset 16 onwards. Add a test to ensure that the supplied firmware is long enough to contain the header and the data stream. On failure, log an error and return `-EINVAL`. Note: The firmware loading was totally broken before commit ac584af59945 ("staging: comedi: me4000: fix firmware downloading"), but that is the most sensible target for this fix. | |||||
| CVE-2026-31746 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: s390/zcrypt: Fix memory leak with CCA cards used as accelerator Tests showed that there is a memory leak if CCA cards are used as accelerator for clear key RSA requests (ME and CRT). With the last rework for the memory allocation the AP messages are allocated by ap_init_apmsg() but for some reason on two places (ME and CRT) the older allocation was still in place. So the first allocation simple was never freed. | |||||
| CVE-2026-31745 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: reset: gpio: fix double free in reset_add_gpio_aux_device() error path When __auxiliary_device_add() fails, reset_add_gpio_aux_device() calls auxiliary_device_uninit(adev). The device release callback reset_gpio_aux_device_release() frees adev, but the current error path then calls kfree(adev) again, causing a double free. Keep kfree(adev) for the auxiliary_device_init() failure path, but avoid freeing adev after auxiliary_device_uninit(). | |||||
| CVE-2026-31744 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: PM: EM: Fix NULL pointer dereference when perf domain ID is not found dev_energymodel_nl_get_perf_domains_doit() calls em_perf_domain_get_by_id() but does not check the return value before passing it to __em_nl_get_pd_size(). When a caller supplies a non-existent perf domain ID, em_perf_domain_get_by_id() returns NULL, and __em_nl_get_pd_size() immediately dereferences pd->cpus (struct offset 0x30), causing a NULL pointer dereference. The sister handler dev_energymodel_nl_get_perf_table_doit() already handles this correctly via __em_nl_get_pd_table_id(), which returns NULL and causes the caller to return -EINVAL. Add the same NULL check in the get-perf-domains do handler. [ rjw: Subject and changelog edits ] | |||||
| CVE-2026-31743 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: nvmem: zynqmp_nvmem: Fix buffer size in DMA and memcpy Buffer size used in dma allocation and memcpy is wrong. It can lead to undersized DMA buffer access and possible memory corruption. use correct buffer size in dma_alloc_coherent and memcpy. | |||||
| CVE-2026-31742 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: vt: discard stale unicode buffer on alt screen exit after resize When enter_alt_screen() saves vc_uni_lines into vc_saved_uni_lines and sets vc_uni_lines to NULL, a subsequent console resize via vc_do_resize() skips reallocating the unicode buffer because vc_uni_lines is NULL. However, vc_saved_uni_lines still points to the old buffer allocated for the original dimensions. When leave_alt_screen() later restores vc_saved_uni_lines, the buffer dimensions no longer match vc_rows/vc_cols. Any operation that iterates over the unicode buffer using the current dimensions (e.g. csi_J clearing the screen) will access memory out of bounds, causing a kernel oops: BUG: unable to handle page fault for address: 0x0000002000000020 RIP: 0010:csi_J+0x133/0x2d0 The faulting address 0x0000002000000020 is two adjacent u32 space characters (0x20) interpreted as a pointer, read from the row data area past the end of the 25-entry pointer array in a buffer allocated for 80x25 but accessed with 240x67 dimensions. Fix this by checking whether the console dimensions changed while in the alternate screen. If they did, free the stale saved buffer instead of restoring it. The unicode screen will be lazily rebuilt via vc_uniscr_check() when next needed. | |||||
| CVE-2026-31741 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: counter: rz-mtu3-cnt: prevent counter from being toggled multiple times Runtime PM counter is incremented / decremented each time the sysfs enable file is written to. If user writes 0 to the sysfs enable file multiple times, runtime PM usage count underflows, generating the following message. rz-mtu3-counter rz-mtu3-counter.0: Runtime PM usage count underflow! At the same time, hardware registers end up being accessed with clocks off in rz_mtu3_terminate_counter() to disable an already disabled channel. If user writes 1 to the sysfs enable file multiple times, runtime PM usage count will be incremented each time, requiring the same number of 0 writes to get it back to 0. If user writes 0 to the sysfs enable file while PWM is in progress, PWM is stopped without counter being the owner of the underlying MTU3 channel. Check against the cached count_is_enabled value and exit if the user is trying to set the same enable value. | |||||
| CVE-2026-31740 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: counter: rz-mtu3-cnt: do not use struct rz_mtu3_channel's dev member The counter driver can use HW channels 1 and 2, while the PWM driver can use HW channels 0, 1, 2, 3, 4, 6, 7. The dev member is assigned both by the counter driver and the PWM driver for channels 1 and 2, to their own struct device instance, overwriting the previous value. The sub-drivers race to assign their own struct device pointer to the same struct rz_mtu3_channel's dev member. The dev member of struct rz_mtu3_channel is used by the counter sub-driver for runtime PM. Depending on the probe order of the counter and PWM sub-drivers, the dev member may point to the wrong struct device instance, causing the counter sub-driver to do runtime PM actions on the wrong device. To fix this, use the parent pointer of the counter, which is assigned during probe to the correct struct device, not the struct device pointer inside the shared struct rz_mtu3_channel. | |||||
| CVE-2026-31739 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: crypto: tegra - Add missing CRYPTO_ALG_ASYNC The tegra crypto driver failed to set the CRYPTO_ALG_ASYNC on its asynchronous algorithms, causing the crypto API to select them for users that request only synchronous algorithms. This causes crashes (at least). Fix this by adding the flag like what the other drivers do. Also remove the unnecessary CRYPTO_ALG_TYPE_* flags, since those just get ignored and overridden by the registration function anyway. | |||||
| CVE-2026-31738 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: vxlan: validate ND option lengths in vxlan_na_create vxlan_na_create() walks ND options according to option-provided lengths. A malformed option can make the parser advance beyond the computed option span or use a too-short source LLADDR option payload. Validate option lengths against the remaining NS option area before advancing, and only read source LLADDR when the option is large enough for an Ethernet address. | |||||
| CVE-2026-31736 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_ppe: avoid NULL deref when gmac0 is disabled If the gmac0 is disabled, the precheck for a valid ingress device will cause a NULL pointer deref and crash the system. This happens because eth->netdev[0] will be NULL but the code will directly try to access netdev_ops. Instead of just checking for the first net_device, it must be checked if any of the mtk_eth net_devices is matching the netdev_ops of the ingress device. | |||||
| CVE-2026-31735 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: iommupt: Fix short gather if the unmap goes into a large mapping unmap has the odd behavior that it can unmap more than requested if the ending point lands within the middle of a large or contiguous IOPTE. In this case the gather should flush everything unmapped which can be larger than what was requested to be unmapped. The gather was only flushing the range requested to be unmapped, not extending to the extra range, resulting in a short invalidation if the caller hits this special condition. This was found by the new invalidation/gather test I am adding in preparation for ARMv8. Claude deduced the root cause. As far as I remember nothing relies on unmapping a large entry, so this is likely not a triggerable bug. | |||||
| CVE-2026-31734 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix is_bpf_migration_disabled() false negative on non-PREEMPT_RCU Since commit 8e4f0b1ebcf2 ("bpf: use rcu_read_lock_dont_migrate() for trampoline.c"), the BPF prolog (__bpf_prog_enter) calls migrate_disable() only when CONFIG_PREEMPT_RCU is enabled, via rcu_read_lock_dont_migrate(). Without CONFIG_PREEMPT_RCU, the prolog never touches migration_disabled, so migration_disabled == 1 always means the task is truly migration-disabled regardless of whether it is the current task. The old unconditional p == current check was a false negative in this case, potentially allowing a migration-disabled task to be dispatched to a remote CPU and triggering scx_error in task_can_run_on_remote_rq(). Only apply the p == current disambiguation when CONFIG_PREEMPT_RCU is enabled, where the ambiguity with the BPF prolog still exists. | |||||
| CVE-2026-31733 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix stale direct dispatch state in ddsp_dsq_id @p->scx.ddsp_dsq_id can be left set (non-SCX_DSQ_INVALID) triggering a spurious warning in mark_direct_dispatch() when the next wakeup's ops.select_cpu() calls scx_bpf_dsq_insert(), such as: WARNING: kernel/sched/ext.c:1273 at scx_dsq_insert_commit+0xcd/0x140 The root cause is that ddsp_dsq_id was only cleared in dispatch_enqueue(), which is not reached in all paths that consume or cancel a direct dispatch verdict. Fix it by clearing it at the right places: - direct_dispatch(): cache the direct dispatch state in local variables and clear it before dispatch_enqueue() on the synchronous path. For the deferred path, the direct dispatch state must remain set until process_ddsp_deferred_locals() consumes them. - process_ddsp_deferred_locals(): cache the dispatch state in local variables and clear it before calling dispatch_to_local_dsq(), which may migrate the task to another rq. - do_enqueue_task(): clear the dispatch state on the enqueue path (local/global/bypass fallbacks), where the direct dispatch verdict is ignored. - dequeue_task_scx(): clear the dispatch state after dispatch_dequeue() to handle both the deferred dispatch cancellation and the holding_cpu race, covering all cases where a pending direct dispatch is cancelled. - scx_disable_task(): clear the direct dispatch state when transitioning a task out of the current scheduler. Waking tasks may have had the direct dispatch state set by the outgoing scheduler's ops.select_cpu() and then been queued on a wake_list via ttwu_queue_wakelist(), when SCX_OPS_ALLOW_QUEUED_WAKEUP is set. Such tasks are not on the runqueue and are not iterated by scx_bypass(), so their direct dispatch state won't be cleared. Without this clear, any subsequent SCX scheduler that tries to direct dispatch the task will trigger the WARN_ON_ONCE() in mark_direct_dispatch(). | |||||
| CVE-2026-31731 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: thermal: core: Address thermal zone removal races with resume Since thermal_zone_pm_complete() and thermal_zone_device_resume() re-initialize the poll_queue delayed work for the given thermal zone, the cancel_delayed_work_sync() in thermal_zone_device_unregister() may miss some already running work items and the thermal zone may be freed prematurely [1]. There are two failing scenarios that both start with running thermal_pm_notify_complete() right before invoking thermal_zone_device_unregister() for one of the thermal zones. In the first scenario, there is a work item already running for the given thermal zone when thermal_pm_notify_complete() calls thermal_zone_pm_complete() for that thermal zone and it continues to run when thermal_zone_device_unregister() starts. Since the poll_queue delayed work has been re-initialized by thermal_pm_notify_complete(), the running work item will be missed by the cancel_delayed_work_sync() in thermal_zone_device_unregister() and if it continues to run past the freeing of the thermal zone object, a use-after-free will occur. In the second scenario, thermal_zone_device_resume() queued up by thermal_pm_notify_complete() runs right after the thermal_zone_exit() called by thermal_zone_device_unregister() has returned. The poll_queue delayed work is re-initialized by it before cancel_delayed_work_sync() is called by thermal_zone_device_unregister(), so it may continue to run after the freeing of the thermal zone object, which also leads to a use-after-free. Address the first failing scenario by ensuring that no thermal work items will be running when thermal_pm_notify_complete() is called. For this purpose, first move the cancel_delayed_work() call from thermal_zone_pm_complete() to thermal_zone_pm_prepare() to prevent new work from entering the workqueue going forward. Next, switch over to using a dedicated workqueue for thermal events and update the code in thermal_pm_notify() to flush that workqueue after thermal_pm_notify_prepare() has returned which will take care of all leftover thermal work already on the workqueue (that leftover work would do nothing useful anyway because all of the thermal zones have been flagged as suspended). The second failing scenario is addressed by adding a tz->state check to thermal_zone_device_resume() to prevent it from re-initializing the poll_queue delayed work if the thermal zone is going away. Note that the above changes will also facilitate relocating the suspend and resume of thermal zones closer to the suspend and resume of devices, respectively. | |||||
| CVE-2026-31730 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: possible double-free of cctx->remote_heap fastrpc_init_create_static_process() may free cctx->remote_heap on the err_map path but does not clear the pointer. Later, fastrpc_rpmsg_remove() frees cctx->remote_heap again if it is non-NULL, which can lead to a double-free if the INIT_CREATE_STATIC ioctl hits the error path and the rpmsg device is subsequently removed/unbound. Clear cctx->remote_heap after freeing it in the error path to prevent the later cleanup from freeing it again. This issue was found by an in-house analysis workflow that extracts AST-based information and runs static checks, with LLM assistance for triage, and was confirmed by manual code review. No hardware testing was performed. | |||||