Total
36333 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2026-23386 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: gve: fix incorrect buffer cleanup in gve_tx_clean_pending_packets for QPL In DQ-QPL mode, gve_tx_clean_pending_packets() incorrectly uses the RDA buffer cleanup path. It iterates num_bufs times and attempts to unmap entries in the dma array. This leads to two issues: 1. The dma array shares storage with tx_qpl_buf_ids (union). Interpreting buffer IDs as DMA addresses results in attempting to unmap incorrect memory locations. 2. num_bufs in QPL mode (counting 2K chunks) can significantly exceed the size of the dma array, causing out-of-bounds access warnings (trace below is how we noticed this issue). UBSAN: array-index-out-of-bounds in drivers/net/ethernet/drivers/net/ethernet/google/gve/gve_tx_dqo.c:178:5 index 18 is out of range for type 'dma_addr_t[18]' (aka 'unsigned long long[18]') Workqueue: gve gve_service_task [gve] Call Trace: <TASK> dump_stack_lvl+0x33/0xa0 __ubsan_handle_out_of_bounds+0xdc/0x110 gve_tx_stop_ring_dqo+0x182/0x200 [gve] gve_close+0x1be/0x450 [gve] gve_reset+0x99/0x120 [gve] gve_service_task+0x61/0x100 [gve] process_scheduled_works+0x1e9/0x380 Fix this by properly checking for QPL mode and delegating to gve_free_tx_qpl_bufs() to reclaim the buffers. | |||||
| CVE-2026-23383 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: bpf, arm64: Force 8-byte alignment for JIT buffer to prevent atomic tearing struct bpf_plt contains a u64 target field. Currently, the BPF JIT allocator requests an alignment of 4 bytes (sizeof(u32)) for the JIT buffer. Because the base address of the JIT buffer can be 4-byte aligned (e.g., ending in 0x4 or 0xc), the relative padding logic in build_plt() fails to ensure that target lands on an 8-byte boundary. This leads to two issues: 1. UBSAN reports misaligned-access warnings when dereferencing the structure. 2. More critically, target is updated concurrently via WRITE_ONCE() in bpf_arch_text_poke() while the JIT'd code executes ldr. On arm64, 64-bit loads/stores are only guaranteed to be single-copy atomic if they are 64-bit aligned. A misaligned target risks a torn read, causing the JIT to jump to a corrupted address. Fix this by increasing the allocation alignment requirement to 8 bytes (sizeof(u64)) in bpf_jit_binary_pack_alloc(). This anchors the base of the JIT buffer to an 8-byte boundary, allowing the relative padding math in build_plt() to correctly align the target field. | |||||
| CVE-2026-23377 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ice: change XDP RxQ frag_size from DMA write length to xdp.frame_sz The only user of frag_size field in XDP RxQ info is bpf_xdp_frags_increase_tail(). It clearly expects whole buff size instead of DMA write size. Different assumptions in ice driver configuration lead to negative tailroom. This allows to trigger kernel panic, when using XDP_ADJUST_TAIL_GROW_MULTI_BUFF xskxceiver test and changing packet size to 6912 and the requested offset to a huge value, e.g. XSK_UMEM__MAX_FRAME_SIZE * 100. Due to other quirks of the ZC configuration in ice, panic is not observed in ZC mode, but tailroom growing still fails when it should not. Use fill queue buffer truesize instead of DMA write size in XDP RxQ info. Fix ZC mode too by using the new helper. | |||||
| CVE-2026-23376 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: nvmet-fcloop: Check remoteport port_state before calling done callback In nvme_fc_handle_ls_rqst_work, the lsrsp->done callback is only set when remoteport->port_state is FC_OBJSTATE_ONLINE. Otherwise, the nvme_fc_xmt_ls_rsp's LLDD call to lport->ops->xmt_ls_rsp is expected to fail and the nvme-fc transport layer itself will directly call nvme_fc_xmt_ls_rsp_free instead of relying on LLDD's done callback to free the lsrsp resources. Update the fcloop_t2h_xmt_ls_rsp routine to check remoteport->port_state. If online, then lsrsp->done callback will free the lsrsp. Else, return -ENODEV to signal the nvme-fc transport to handle freeing lsrsp. | |||||
| CVE-2026-23374 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: blktrace: fix __this_cpu_read/write in preemptible context tracing_record_cmdline() internally uses __this_cpu_read() and __this_cpu_write() on the per-CPU variable trace_cmdline_save, and trace_save_cmdline() explicitly asserts preemption is disabled via lockdep_assert_preemption_disabled(). These operations are only safe when preemption is off, as they were designed to be called from the scheduler context (probe_wakeup_sched_switch() / probe_wakeup()). __blk_add_trace() was calling tracing_record_cmdline(current) early in the blk_tracer path, before ring buffer reservation, from process context where preemption is fully enabled. This triggers the following using blktests/blktrace/002: blktrace/002 (blktrace ftrace corruption with sysfs trace) [failed] runtime 0.367s ... 0.437s something found in dmesg: [ 81.211018] run blktests blktrace/002 at 2026-02-25 22:24:33 [ 81.239580] null_blk: disk nullb1 created [ 81.357294] BUG: using __this_cpu_read() in preemptible [00000000] code: dd/2516 [ 81.362842] caller is tracing_record_cmdline+0x10/0x40 [ 81.362872] CPU: 16 UID: 0 PID: 2516 Comm: dd Tainted: G N 7.0.0-rc1lblk+ #84 PREEMPT(full) [ 81.362877] Tainted: [N]=TEST [ 81.362878] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014 [ 81.362881] Call Trace: [ 81.362884] <TASK> [ 81.362886] dump_stack_lvl+0x8d/0xb0 ... (See '/mnt/sda/blktests/results/nodev/blktrace/002.dmesg' for the entire message) [ 81.211018] run blktests blktrace/002 at 2026-02-25 22:24:33 [ 81.239580] null_blk: disk nullb1 created [ 81.357294] BUG: using __this_cpu_read() in preemptible [00000000] code: dd/2516 [ 81.362842] caller is tracing_record_cmdline+0x10/0x40 [ 81.362872] CPU: 16 UID: 0 PID: 2516 Comm: dd Tainted: G N 7.0.0-rc1lblk+ #84 PREEMPT(full) [ 81.362877] Tainted: [N]=TEST [ 81.362878] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014 [ 81.362881] Call Trace: [ 81.362884] <TASK> [ 81.362886] dump_stack_lvl+0x8d/0xb0 [ 81.362895] check_preemption_disabled+0xce/0xe0 [ 81.362902] tracing_record_cmdline+0x10/0x40 [ 81.362923] __blk_add_trace+0x307/0x5d0 [ 81.362934] ? lock_acquire+0xe0/0x300 [ 81.362940] ? iov_iter_extract_pages+0x101/0xa30 [ 81.362959] blk_add_trace_bio+0x106/0x1e0 [ 81.362968] submit_bio_noacct_nocheck+0x24b/0x3a0 [ 81.362979] ? lockdep_init_map_type+0x58/0x260 [ 81.362988] submit_bio_wait+0x56/0x90 [ 81.363009] __blkdev_direct_IO_simple+0x16c/0x250 [ 81.363026] ? __pfx_submit_bio_wait_endio+0x10/0x10 [ 81.363038] ? rcu_read_lock_any_held+0x73/0xa0 [ 81.363051] blkdev_read_iter+0xc1/0x140 [ 81.363059] vfs_read+0x20b/0x330 [ 81.363083] ksys_read+0x67/0xe0 [ 81.363090] do_syscall_64+0xbf/0xf00 [ 81.363102] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 81.363106] RIP: 0033:0x7f281906029d [ 81.363111] Code: 31 c0 e9 c6 fe ff ff 50 48 8d 3d 66 63 0a 00 e8 59 ff 01 00 66 0f 1f 84 00 00 00 00 00 80 3d 41 33 0e 00 00 74 17 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 5b c3 66 2e 0f 1f 84 00 00 00 00 00 48 83 ec [ 81.363113] RSP: 002b:00007ffca127dd48 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 [ 81.363120] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f281906029d [ 81.363122] RDX: 0000000000001000 RSI: 0000559f8bfae000 RDI: 0000000000000000 [ 81.363123] RBP: 0000000000001000 R08: 0000002863a10a81 R09: 00007f281915f000 [ 81.363124] R10: 00007f2818f77b60 R11: 0000000000000246 R12: 0000559f8bfae000 [ 81.363126] R13: 0000000000000000 R14: 0000000000000000 R15: 000000000000000a [ 81.363142] </TASK> The same BUG fires from blk_add_trace_plug(), blk_add_trace_unplug(), and blk_add_trace_rq() paths as well. The purpose of tracin ---truncated--- | |||||
| CVE-2026-23373 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: wifi: rsi: Don't default to -EOPNOTSUPP in rsi_mac80211_config This triggers a WARN_ON in ieee80211_hw_conf_init and isn't the expected behavior from the driver - other drivers default to 0 too. | |||||
| CVE-2026-23372 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: nfc: rawsock: cancel tx_work before socket teardown In rawsock_release(), cancel any pending tx_work and purge the write queue before orphaning the socket. rawsock_tx_work runs on the system workqueue and calls nfc_data_exchange which dereferences the NCI device. Without synchronization, tx_work can race with socket and device teardown when a process is killed (e.g. by SIGKILL), leading to use-after-free or leaked references. Set SEND_SHUTDOWN first so that if tx_work is already running it will see the flag and skip transmitting, then use cancel_work_sync to wait for any in-progress execution to finish, and finally purge any remaining queued skbs. | |||||
| CVE-2026-23371 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: sched/deadline: Fix missing ENQUEUE_REPLENISH during PI de-boosting Running stress-ng --schedpolicy 0 on an RT kernel on a big machine might lead to the following WARNINGs (edited). sched: DL de-boosted task PID 22725: REPLENISH flag missing WARNING: CPU: 93 PID: 0 at kernel/sched/deadline.c:239 dequeue_task_dl+0x15c/0x1f8 ... (running_bw underflow) Call trace: dequeue_task_dl+0x15c/0x1f8 (P) dequeue_task+0x80/0x168 deactivate_task+0x24/0x50 push_dl_task+0x264/0x2e0 dl_task_timer+0x1b0/0x228 __hrtimer_run_queues+0x188/0x378 hrtimer_interrupt+0xfc/0x260 ... The problem is that when a SCHED_DEADLINE task (lock holder) is changed to a lower priority class via sched_setscheduler(), it may fail to properly inherit the parameters of potential DEADLINE donors if it didn't already inherit them in the past (shorter deadline than donor's at that time). This might lead to bandwidth accounting corruption, as enqueue_task_dl() won't recognize the lock holder as boosted. The scenario occurs when: 1. A DEADLINE task (donor) blocks on a PI mutex held by another DEADLINE task (holder), but the holder doesn't inherit parameters (e.g., it already has a shorter deadline) 2. sched_setscheduler() changes the holder from DEADLINE to a lower class while still holding the mutex 3. The holder should now inherit DEADLINE parameters from the donor and be enqueued with ENQUEUE_REPLENISH, but this doesn't happen Fix the issue by introducing __setscheduler_dl_pi(), which detects when a DEADLINE (proper or boosted) task gets setscheduled to a lower priority class. In case, the function makes the task inherit DEADLINE parameters of the donoer (pi_se) and sets ENQUEUE_REPLENISH flag to ensure proper bandwidth accounting during the next enqueue operation. | |||||
| CVE-2026-23367 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: wifi: radiotap: reject radiotap with unknown bits The radiotap parser is currently only used with the radiotap namespace (not with vendor namespaces), but if the undefined field 18 is used, the alignment/size is unknown as well. In this case, iterator->_next_ns_data isn't initialized (it's only set for skipping vendor namespaces), and syzbot points out that we later compare against this uninitialized value. Fix this by moving the rejection of unknown radiotap fields down to after the in-namespace lookup, so it will really use iterator->_next_ns_data only for vendor namespaces, even in case undefined fields are present. | |||||
| CVE-2026-23355 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ata: libata: cancel pending work after clearing deferred_qc Syzbot reported a WARN_ON() in ata_scsi_deferred_qc_work(), caused by ap->ops->qc_defer() returning non-zero before issuing the deferred qc. ata_scsi_schedule_deferred_qc() is called during each command completion. This function will check if there is a deferred QC, and if ap->ops->qc_defer() returns zero, meaning that it is possible to queue the deferred qc at this time (without being deferred), then it will queue the work which will issue the deferred qc. Once the work get to run, which can potentially be a very long time after the work was scheduled, there is a WARN_ON() if ap->ops->qc_defer() returns non-zero. While we hold the ap->lock both when assigning and clearing deferred_qc, and the work itself holds the ap->lock, the code currently does not cancel the work after clearing the deferred qc. This means that the following scenario can happen: 1) One or several NCQ commands are queued. 2) A non-NCQ command is queued, gets stored in ap->deferred_qc. 3) Last NCQ command gets completed, work is queued to issue the deferred qc. 4) Timeout or error happens, ap->deferred_qc is cleared. The queued work is currently NOT canceled. 5) Port is reset. 6) One or several NCQ commands are queued. 7) A non-NCQ command is queued, gets stored in ap->deferred_qc. 8) Work is finally run. Yet at this time, there is still NCQ commands in flight. The work in 8) really belongs to the non-NCQ command in 2), not to the non-NCQ command in 7). The reason why the work is executed when it is not supposed to, is because it was never canceled when ap->deferred_qc was cleared in 4). Thus, ensure that we always cancel the work after clearing ap->deferred_qc. Another potential fix would have been to let ata_scsi_deferred_qc_work() do nothing if ap->ops->qc_defer() returns non-zero. However, canceling the work when clearing ap->deferred_qc seems slightly more logical, as we hold the ap->lock when clearing ap->deferred_qc, so we know that the work cannot be holding the lock. (The function could be waiting for the lock, but that is okay since it will do nothing if ap->deferred_qc is not set.) | |||||
| CVE-2026-23347 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: can: usb: f81604: correctly anchor the urb in the read bulk callback When submitting an urb, that is using the anchor pattern, it needs to be anchored before submitting it otherwise it could be leaked if usb_kill_anchored_urbs() is called. This logic is correctly done elsewhere in the driver, except in the read bulk callback so do that here also. | |||||
| CVE-2026-23345 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: arm64: gcs: Do not set PTE_SHARED on GCS mappings if FEAT_LPA2 is enabled When FEAT_LPA2 is enabled, bits 8-9 of the PTE replace the shareability attribute with bits 50-51 of the output address. The _PAGE_GCS{,_RO} definitions include the PTE_SHARED bits as 0b11 (this matches the other _PAGE_* definitions) but using this macro directly leads to the following panic when enabling GCS on a system/model with LPA2: Unable to handle kernel paging request at virtual address fffff1ffc32d8008 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 swapper pgtable: 4k pages, 52-bit VAs, pgdp=0000000060f4d000 [fffff1ffc32d8008] pgd=100000006184b003, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] SMP CPU: 0 UID: 0 PID: 513 Comm: gcs_write_fault Tainted: G M 7.0.0-rc1 #1 PREEMPT Tainted: [M]=MACHINE_CHECK Hardware name: QEMU QEMU Virtual Machine, BIOS 2025.02-8+deb13u1 11/08/2025 pstate: 03402005 (nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : zap_huge_pmd+0x168/0x468 lr : zap_huge_pmd+0x2c/0x468 sp : ffff800080beb660 x29: ffff800080beb660 x28: fff00000c2058180 x27: ffff800080beb898 x26: fff00000c2058180 x25: ffff800080beb820 x24: 00c800010b600f41 x23: ffffc1ffc30af1a8 x22: fff00000c2058180 x21: 0000ffff8dc00000 x20: fff00000c2bc6370 x19: ffff800080beb898 x18: ffff800080bebb60 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000007 x14: 000000000000000a x13: 0000aaaacbbbffff x12: 0000000000000000 x11: 0000ffff8ddfffff x10: 00000000000001fe x9 : 0000ffff8ddfffff x8 : 0000ffff8de00000 x7 : 0000ffff8da00000 x6 : fff00000c2bc6370 x5 : 0000ffff8da00000 x4 : 000000010b600000 x3 : ffffc1ffc0000000 x2 : fff00000c2058180 x1 : fffff1ffc32d8000 x0 : 000000c00010b600 Call trace: zap_huge_pmd+0x168/0x468 (P) unmap_page_range+0xd70/0x1560 unmap_single_vma+0x48/0x80 unmap_vmas+0x90/0x180 unmap_region+0x88/0xe4 vms_complete_munmap_vmas+0xf8/0x1e0 do_vmi_align_munmap+0x158/0x180 do_vmi_munmap+0xac/0x160 __vm_munmap+0xb0/0x138 vm_munmap+0x14/0x20 gcs_free+0x70/0x80 mm_release+0x1c/0xc8 exit_mm_release+0x28/0x38 do_exit+0x190/0x8ec do_group_exit+0x34/0x90 get_signal+0x794/0x858 arch_do_signal_or_restart+0x11c/0x3e0 exit_to_user_mode_loop+0x10c/0x17c el0_da+0x8c/0x9c el0t_64_sync_handler+0xd0/0xf0 el0t_64_sync+0x198/0x19c Code: aa1603e2 d34cfc00 cb813001 8b011861 (f9400420) Similarly to how the kernel handles protection_map[], use a gcs_page_prot variable to store the protection bits and clear PTE_SHARED if LPA2 is enabled. Also remove the unused PAGE_GCS{,_RO} macros. | |||||
| CVE-2026-23338 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/userq: Do not allow userspace to trivially triger kernel warnings Userspace can either deliberately pass in the too small num_fences, or the required number can legitimately grow between the two calls to the userq wait ioctl. In both cases we do not want the emit the kernel warning backtrace since nothing is wrong with the kernel and userspace will simply get an errno reported back. So lets simply drop the WARN_ONs. (cherry picked from commit 2c333ea579de6cc20ea7bc50e9595ef72863e65c) | |||||
| CVE-2026-23334 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: can: usb: f81604: handle short interrupt urb messages properly If an interrupt urb is received that is not the correct length, properly detect it and don't attempt to treat the data as valid. | |||||
| CVE-2026-23331 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: udp: Unhash auto-bound connected sk from 4-tuple hash table when disconnected. Let's say we bind() an UDP socket to the wildcard address with a non-zero port, connect() it to an address, and disconnect it from the address. bind() sets SOCK_BINDPORT_LOCK on sk->sk_userlocks (but not SOCK_BINDADDR_LOCK), and connect() calls udp_lib_hash4() to put the socket into the 4-tuple hash table. Then, __udp_disconnect() calls sk->sk_prot->rehash(sk). It computes a new hash based on the wildcard address and moves the socket to a new slot in the 4-tuple hash table, leaving a garbage in the chain that no packet hits. Let's remove such a socket from 4-tuple hash table when disconnected. Note that udp_sk(sk)->udp_portaddr_hash needs to be udpated after udp_hash4_dec(hslot2) in udp_unhash4(). | |||||
| CVE-2026-23329 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: libie: don't unroll if fwlog isn't supported The libie_fwlog_deinit() function can be called during driver unload even when firmware logging was never properly initialized. This led to call trace: [ 148.576156] Oops: Oops: 0000 [#1] SMP NOPTI [ 148.576167] CPU: 80 UID: 0 PID: 12843 Comm: rmmod Kdump: loaded Not tainted 6.17.0-rc7next-queue-3oct-01915-g06d79d51cf51 #1 PREEMPT(full) [ 148.576177] Hardware name: HPE ProLiant DL385 Gen10 Plus/ProLiant DL385 Gen10 Plus, BIOS A42 07/18/2020 [ 148.576182] RIP: 0010:__dev_printk+0x16/0x70 [ 148.576196] Code: 1f 44 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 41 55 41 54 49 89 d4 55 48 89 fd 53 48 85 f6 74 3c <4c> 8b 6e 50 48 89 f3 4d 85 ed 75 03 4c 8b 2e 48 89 df e8 f3 27 98 [ 148.576204] RSP: 0018:ffffd2fd7ea17a48 EFLAGS: 00010202 [ 148.576211] RAX: ffffd2fd7ea17aa0 RBX: ffff8eb288ae2000 RCX: 0000000000000000 [ 148.576217] RDX: ffffd2fd7ea17a70 RSI: 00000000000000c8 RDI: ffffffffb68d3d88 [ 148.576222] RBP: ffffffffb68d3d88 R08: 0000000000000000 R09: 0000000000000000 [ 148.576227] R10: 00000000000000c8 R11: ffff8eb2b1a49400 R12: ffffd2fd7ea17a70 [ 148.576231] R13: ffff8eb3141fb000 R14: ffffffffc1215b48 R15: ffffffffc1215bd8 [ 148.576236] FS: 00007f5666ba6740(0000) GS:ffff8eb2472b9000(0000) knlGS:0000000000000000 [ 148.576242] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 148.576247] CR2: 0000000000000118 CR3: 000000011ad17000 CR4: 0000000000350ef0 [ 148.576252] Call Trace: [ 148.576258] <TASK> [ 148.576269] _dev_warn+0x7c/0x96 [ 148.576290] libie_fwlog_deinit+0x112/0x117 [libie_fwlog] [ 148.576303] ixgbe_remove+0x63/0x290 [ixgbe] [ 148.576342] pci_device_remove+0x42/0xb0 [ 148.576354] device_release_driver_internal+0x19c/0x200 [ 148.576365] driver_detach+0x48/0x90 [ 148.576372] bus_remove_driver+0x6d/0xf0 [ 148.576383] pci_unregister_driver+0x2e/0xb0 [ 148.576393] ixgbe_exit_module+0x1c/0xd50 [ixgbe] [ 148.576430] __do_sys_delete_module.isra.0+0x1bc/0x2e0 [ 148.576446] do_syscall_64+0x7f/0x980 It can be reproduced by trying to unload ixgbe driver in recovery mode. Fix that by checking if fwlog is supported before doing unroll. | |||||
| CVE-2026-23324 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: can: usb: etas_es58x: correctly anchor the urb in the read bulk callback When submitting an urb, that is using the anchor pattern, it needs to be anchored before submitting it otherwise it could be leaked if usb_kill_anchored_urbs() is called. This logic is correctly done elsewhere in the driver, except in the read bulk callback so do that here also. | |||||
| CVE-2026-23316 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: ipv4: fix ARM64 alignment fault in multipath hash seed `struct sysctl_fib_multipath_hash_seed` contains two u32 fields (user_seed and mp_seed), making it an 8-byte structure with a 4-byte alignment requirement. In `fib_multipath_hash_from_keys()`, the code evaluates the entire struct atomically via `READ_ONCE()`: mp_seed = READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_seed).mp_seed; While this silently works on GCC by falling back to unaligned regular loads which the ARM64 kernel tolerates, it causes a fatal kernel panic when compiled with Clang and LTO enabled. Commit e35123d83ee3 ("arm64: lto: Strengthen READ_ONCE() to acquire when CONFIG_LTO=y") strengthens `READ_ONCE()` to use Load-Acquire instructions (`ldar` / `ldapr`) to prevent compiler reordering bugs under Clang LTO. Since the macro evaluates the full 8-byte struct, Clang emits a 64-bit `ldar` instruction. ARM64 architecture strictly requires `ldar` to be naturally aligned, thus executing it on a 4-byte aligned address triggers a strict Alignment Fault (FSC = 0x21). Fix the read side by moving the `READ_ONCE()` directly to the `u32` member, which emits a safe 32-bit `ldar Wn`. Furthermore, Eric Dumazet pointed out that `WRITE_ONCE()` on the entire struct in `proc_fib_multipath_hash_set_seed()` is also flawed. Analysis shows that Clang splits this 8-byte write into two separate 32-bit `str` instructions. While this avoids an alignment fault, it destroys atomicity and exposes a tear-write vulnerability. Fix this by explicitly splitting the write into two 32-bit `WRITE_ONCE()` operations. Finally, add the missing `READ_ONCE()` when reading `user_seed` in `proc_fib_multipath_hash_seed()` to ensure proper pairing and concurrency safety. | |||||
| CVE-2026-23312 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: usb: kaweth: validate USB endpoints The kaweth driver should validate that the device it is probing has the proper number and types of USB endpoints it is expecting before it binds to it. If a malicious device were to not have the same urbs the driver will crash later on when it blindly accesses these endpoints. | |||||
| CVE-2026-23308 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: pinctrl: equilibrium: fix warning trace on load The callback functions 'eqbr_irq_mask()' and 'eqbr_irq_ack()' are also called in the callback function 'eqbr_irq_mask_ack()'. This is done to avoid source code duplication. The problem, is that in the function 'eqbr_irq_mask()' also calles the gpiolib function 'gpiochip_disable_irq()' This generates the following warning trace in the log for every gpio on load. [ 6.088111] ------------[ cut here ]------------ [ 6.092440] WARNING: CPU: 3 PID: 1 at drivers/gpio/gpiolib.c:3810 gpiochip_disable_irq+0x39/0x50 [ 6.097847] Modules linked in: [ 6.097847] CPU: 3 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.12.59+ #0 [ 6.097847] Tainted: [W]=WARN [ 6.097847] RIP: 0010:gpiochip_disable_irq+0x39/0x50 [ 6.097847] Code: 39 c6 48 19 c0 21 c6 48 c1 e6 05 48 03 b2 38 03 00 00 48 81 fe 00 f0 ff ff 77 11 48 8b 46 08 f6 c4 02 74 06 f0 80 66 09 fb c3 <0f> 0b 90 0f 1f 40 00 c3 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 [ 6.097847] RSP: 0000:ffffc9000000b830 EFLAGS: 00010046 [ 6.097847] RAX: 0000000000000045 RBX: ffff888001be02a0 RCX: 0000000000000008 [ 6.097847] RDX: ffff888001be9000 RSI: ffff888001b2dd00 RDI: ffff888001be02a0 [ 6.097847] RBP: ffffc9000000b860 R08: 0000000000000000 R09: 0000000000000000 [ 6.097847] R10: 0000000000000001 R11: ffff888001b2a154 R12: ffff888001be0514 [ 6.097847] R13: ffff888001be02a0 R14: 0000000000000008 R15: 0000000000000000 [ 6.097847] FS: 0000000000000000(0000) GS:ffff888041d80000(0000) knlGS:0000000000000000 [ 6.097847] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6.097847] CR2: 0000000000000000 CR3: 0000000003030000 CR4: 00000000001026b0 [ 6.097847] Call Trace: [ 6.097847] <TASK> [ 6.097847] ? eqbr_irq_mask+0x63/0x70 [ 6.097847] ? no_action+0x10/0x10 [ 6.097847] eqbr_irq_mask_ack+0x11/0x60 In an other driver (drivers/pinctrl/starfive/pinctrl-starfive-jh7100.c) the interrupt is not disabled here. To fix this, do not call the 'eqbr_irq_mask()' and 'eqbr_irq_ack()' function. Implement instead this directly without disabling the interrupts. | |||||