Total
396511 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2024-35982 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: batman-adv: Avoid infinite loop trying to resize local TT If the MTU of one of an attached interface becomes too small to transmit the local translation table then it must be resized to fit inside all fragments (when enabled) or a single packet. But if the MTU becomes too low to transmit even the header + the VLAN specific part then the resizing of the local TT will never succeed. This can for example happen when the usable space is 110 bytes and 11 VLANs are on top of batman-adv. In this case, at least 116 byte would be needed. There will just be an endless spam of batman_adv: batadv0: Forced to purge local tt entries to fit new maximum fragment MTU (110) in the log but the function will never finish. Problem here is that the timeout will be halved all the time and will then stagnate at 0 and therefore never be able to reduce the table even more. There are other scenarios possible with a similar result. The number of BATADV_TT_CLIENT_NOPURGE entries in the local TT can for example be too high to fit inside a packet. Such a scenario can therefore happen also with only a single VLAN + 7 non-purgable addresses - requiring at least 120 bytes. While this should be handled proactively when: * interface with too low MTU is added * VLAN is added * non-purgeable local mac is added * MTU of an attached interface is reduced * fragmentation setting gets disabled (which most likely requires dropping attached interfaces) not all of these scenarios can be prevented because batman-adv is only consuming events without the the possibility to prevent these actions (non-purgable MAC address added, MTU of an attached interface is reduced). It is therefore necessary to also make sure that the code is able to handle also the situations when there were already incompatible system configuration are present. | |||||
| CVE-2024-35981 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: virtio_net: Do not send RSS key if it is not supported There is a bug when setting the RSS options in virtio_net that can break the whole machine, getting the kernel into an infinite loop. Running the following command in any QEMU virtual machine with virtionet will reproduce this problem: # ethtool -X eth0 hfunc toeplitz This is how the problem happens: 1) ethtool_set_rxfh() calls virtnet_set_rxfh() 2) virtnet_set_rxfh() calls virtnet_commit_rss_command() 3) virtnet_commit_rss_command() populates 4 entries for the rss scatter-gather 4) Since the command above does not have a key, then the last scatter-gatter entry will be zeroed, since rss_key_size == 0. sg_buf_size = vi->rss_key_size; 5) This buffer is passed to qemu, but qemu is not happy with a buffer with zero length, and do the following in virtqueue_map_desc() (QEMU function): if (!sz) { virtio_error(vdev, "virtio: zero sized buffers are not allowed"); 6) virtio_error() (also QEMU function) set the device as broken vdev->broken = true; 7) Qemu bails out, and do not repond this crazy kernel. 8) The kernel is waiting for the response to come back (function virtnet_send_command()) 9) The kernel is waiting doing the following : while (!virtqueue_get_buf(vi->cvq, &tmp) && !virtqueue_is_broken(vi->cvq)) cpu_relax(); 10) None of the following functions above is true, thus, the kernel loops here forever. Keeping in mind that virtqueue_is_broken() does not look at the qemu `vdev->broken`, so, it never realizes that the vitio is broken at QEMU side. Fix it by not sending RSS commands if the feature is not available in the device. | |||||
| CVE-2024-35978 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix memory leak in hci_req_sync_complete() In 'hci_req_sync_complete()', always free the previous sync request state before assigning reference to a new one. | |||||
| CVE-2024-35977 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 4.7 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: platform/chrome: cros_ec_uart: properly fix race condition The cros_ec_uart_probe() function calls devm_serdev_device_open() before it calls serdev_device_set_client_ops(). This can trigger a NULL pointer dereference: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... Call Trace: <TASK> ... ? ttyport_receive_buf A simplified version of crashing code is as follows: static inline size_t serdev_controller_receive_buf(struct serdev_controller *ctrl, const u8 *data, size_t count) { struct serdev_device *serdev = ctrl->serdev; if (!serdev || !serdev->ops->receive_buf) // CRASH! return 0; return serdev->ops->receive_buf(serdev, data, count); } It assumes that if SERPORT_ACTIVE is set and serdev exists, serdev->ops will also exist. This conflicts with the existing cros_ec_uart_probe() logic, as it first calls devm_serdev_device_open() (which sets SERPORT_ACTIVE), and only later sets serdev->ops via serdev_device_set_client_ops(). Commit 01f95d42b8f4 ("platform/chrome: cros_ec_uart: fix race condition") attempted to fix a similar race condition, but while doing so, made the window of error for this race condition to happen much wider. Attempt to fix the race condition again, making sure we fully setup before calling devm_serdev_device_open(). | |||||
| CVE-2024-35975 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: Fix transmit scheduler resource leak Inorder to support shaping and scheduling, Upon class creation Netdev driver allocates trasmit schedulers. The previous patch which added support for Round robin scheduling has a bug due to which driver is not freeing transmit schedulers post class deletion. This patch fixes the same. | |||||
| CVE-2024-35974 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: block: fix q->blkg_list corruption during disk rebind Multiple gendisk instances can allocated/added for single request queue in case of disk rebind. blkg may still stay in q->blkg_list when calling blkcg_init_disk() for rebind, then q->blkg_list becomes corrupted. Fix the list corruption issue by: - add blkg_init_queue() to initialize q->blkg_list & q->blkcg_mutex only - move calling blkg_init_queue() into blk_alloc_queue() The list corruption should be started since commit f1c006f1c685 ("blk-cgroup: synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()") which delays removing blkg from q->blkg_list into blkg_free_workfn(). | |||||
| CVE-2024-35973 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: geneve: fix header validation in geneve[6]_xmit_skb syzbot is able to trigger an uninit-value in geneve_xmit() [1] Problem : While most ip tunnel helpers (like ip_tunnel_get_dsfield()) uses skb_protocol(skb, true), pskb_inet_may_pull() is only using skb->protocol. If anything else than ETH_P_IPV6 or ETH_P_IP is found in skb->protocol, pskb_inet_may_pull() does nothing at all. If a vlan tag was provided by the caller (af_packet in the syzbot case), the network header might not point to the correct location, and skb linear part could be smaller than expected. Add skb_vlan_inet_prepare() to perform a complete mac validation. Use this in geneve for the moment, I suspect we need to adopt this more broadly. v4 - Jakub reported v3 broke l2_tos_ttl_inherit.sh selftest - Only call __vlan_get_protocol() for vlan types. v2,v3 - Addressed Sabrina comments on v1 and v2 [1] BUG: KMSAN: uninit-value in geneve_xmit_skb drivers/net/geneve.c:910 [inline] BUG: KMSAN: uninit-value in geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030 geneve_xmit_skb drivers/net/geneve.c:910 [inline] geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547 __dev_queue_xmit+0x348d/0x52c0 net/core/dev.c:4335 dev_queue_xmit include/linux/netdevice.h:3091 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3081 [inline] packet_sendmsg+0x8bb0/0x9ef0 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2199 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 Uninit was created at: slab_post_alloc_hook mm/slub.c:3804 [inline] slab_alloc_node mm/slub.c:3845 [inline] kmem_cache_alloc_node+0x613/0xc50 mm/slub.c:3888 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:577 __alloc_skb+0x35b/0x7a0 net/core/skbuff.c:668 alloc_skb include/linux/skbuff.h:1318 [inline] alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6504 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2795 packet_alloc_skb net/packet/af_packet.c:2930 [inline] packet_snd net/packet/af_packet.c:3024 [inline] packet_sendmsg+0x722d/0x9ef0 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2199 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 CPU: 0 PID: 5033 Comm: syz-executor346 Not tainted 6.9.0-rc1-syzkaller-00005-g928a87efa423 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024 | |||||
| CVE-2024-35972 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: bnxt_en: Fix possible memory leak in bnxt_rdma_aux_device_init() If ulp = kzalloc() fails, the allocated edev will leak because it is not properly assigned and the cleanup path will not be able to free it. Fix it by assigning it properly immediately after allocation. | |||||
| CVE-2024-35970 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 6.3 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: af_unix: Clear stale u->oob_skb. syzkaller started to report deadlock of unix_gc_lock after commit 4090fa373f0e ("af_unix: Replace garbage collection algorithm."), but it just uncovers the bug that has been there since commit 314001f0bf92 ("af_unix: Add OOB support"). The repro basically does the following. from socket import * from array import array c1, c2 = socketpair(AF_UNIX, SOCK_STREAM) c1.sendmsg([b'a'], [(SOL_SOCKET, SCM_RIGHTS, array("i", [c2.fileno()]))], MSG_OOB) c2.recv(1) # blocked as no normal data in recv queue c2.close() # done async and unblock recv() c1.close() # done async and trigger GC A socket sends its file descriptor to itself as OOB data and tries to receive normal data, but finally recv() fails due to async close(). The problem here is wrong handling of OOB skb in manage_oob(). When recvmsg() is called without MSG_OOB, manage_oob() is called to check if the peeked skb is OOB skb. In such a case, manage_oob() pops it out of the receive queue but does not clear unix_sock(sk)->oob_skb. This is wrong in terms of uAPI. Let's say we send "hello" with MSG_OOB, and "world" without MSG_OOB. The 'o' is handled as OOB data. When recv() is called twice without MSG_OOB, the OOB data should be lost. >>> from socket import * >>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM, 0) >>> c1.send(b'hello', MSG_OOB) # 'o' is OOB data 5 >>> c1.send(b'world') 5 >>> c2.recv(5) # OOB data is not received b'hell' >>> c2.recv(5) # OOB date is skipped b'world' >>> c2.recv(5, MSG_OOB) # This should return an error b'o' In the same situation, TCP actually returns -EINVAL for the last recv(). Also, if we do not clear unix_sk(sk)->oob_skb, unix_poll() always set EPOLLPRI even though the data has passed through by previous recv(). To avoid these issues, we must clear unix_sk(sk)->oob_skb when dequeuing it from recv queue. The reason why the old GC did not trigger the deadlock is because the old GC relied on the receive queue to detect the loop. When it is triggered, the socket with OOB data is marked as GC candidate because file refcount == inflight count (1). However, after traversing all inflight sockets, the socket still has a positive inflight count (1), thus the socket is excluded from candidates. Then, the old GC lose the chance to garbage-collect the socket. With the old GC, the repro continues to create true garbage that will never be freed nor detected by kmemleak as it's linked to the global inflight list. That's why we couldn't even notice the issue. | |||||
| CVE-2024-35966 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: Fix not validating setsockopt user input syzbot reported rfcomm_sock_setsockopt_old() is copying data without checking user input length. BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline] BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt_old net/bluetooth/rfcomm/sock.c:632 [inline] BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt+0x893/0xa70 net/bluetooth/rfcomm/sock.c:673 Read of size 4 at addr ffff8880209a8bc3 by task syz-executor632/5064 | |||||
| CVE-2024-35965 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: Fix not validating setsockopt user input Check user input length before copying data. | |||||
| CVE-2024-35964 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: ISO: Fix not validating setsockopt user input Check user input length before copying data. | |||||
| CVE-2024-35961 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Register devlink first under devlink lock In case device is having a non fatal FW error during probe, the driver will report the error to user via devlink. This will trigger a WARN_ON, since mlx5 is calling devlink_register() last. In order to avoid the WARN_ON[1], change mlx5 to invoke devl_register() first under devlink lock. [1] WARNING: CPU: 5 PID: 227 at net/devlink/health.c:483 devlink_recover_notify.constprop.0+0xb8/0xc0 CPU: 5 PID: 227 Comm: kworker/u16:3 Not tainted 6.4.0-rc5_for_upstream_min_debug_2023_06_12_12_38 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5_health0000:08:00.0 mlx5_fw_reporter_err_work [mlx5_core] RIP: 0010:devlink_recover_notify.constprop.0+0xb8/0xc0 Call Trace: <TASK> ? __warn+0x79/0x120 ? devlink_recover_notify.constprop.0+0xb8/0xc0 ? report_bug+0x17c/0x190 ? handle_bug+0x3c/0x60 ? exc_invalid_op+0x14/0x70 ? asm_exc_invalid_op+0x16/0x20 ? devlink_recover_notify.constprop.0+0xb8/0xc0 devlink_health_report+0x4a/0x1c0 mlx5_fw_reporter_err_work+0xa4/0xd0 [mlx5_core] process_one_work+0x1bb/0x3c0 ? process_one_work+0x3c0/0x3c0 worker_thread+0x4d/0x3c0 ? process_one_work+0x3c0/0x3c0 kthread+0xc6/0xf0 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 </TASK> | |||||
| CVE-2024-35960 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 9.1 CRITICAL |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Properly link new fs rules into the tree Previously, add_rule_fg would only add newly created rules from the handle into the tree when they had a refcount of 1. On the other hand, create_flow_handle tries hard to find and reference already existing identical rules instead of creating new ones. These two behaviors can result in a situation where create_flow_handle 1) creates a new rule and references it, then 2) in a subsequent step during the same handle creation references it again, resulting in a rule with a refcount of 2 that is not linked into the tree, will have a NULL parent and root and will result in a crash when the flow group is deleted because del_sw_hw_rule, invoked on rule deletion, assumes node->parent is != NULL. This happened in the wild, due to another bug related to incorrect handling of duplicate pkt_reformat ids, which lead to the code in create_flow_handle incorrectly referencing a just-added rule in the same flow handle, resulting in the problem described above. Full details are at [1]. This patch changes add_rule_fg to add new rules without parents into the tree, properly initializing them and avoiding the crash. This makes it more consistent with how rules are added to an FTE in create_flow_handle. | |||||
| CVE-2024-35959 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix mlx5e_priv_init() cleanup flow When mlx5e_priv_init() fails, the cleanup flow calls mlx5e_selq_cleanup which calls mlx5e_selq_apply() that assures that the `priv->state_lock` is held using lockdep_is_held(). Acquire the state_lock in mlx5e_selq_cleanup(). Kernel log: ============================= WARNING: suspicious RCU usage 6.8.0-rc3_net_next_841a9b5 #1 Not tainted ----------------------------- drivers/net/ethernet/mellanox/mlx5/core/en/selq.c:124 suspicious rcu_dereference_protected() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 2 locks held by systemd-modules/293: #0: ffffffffa05067b0 (devices_rwsem){++++}-{3:3}, at: ib_register_client+0x109/0x1b0 [ib_core] #1: ffff8881096c65c0 (&device->client_data_rwsem){++++}-{3:3}, at: add_client_context+0x104/0x1c0 [ib_core] stack backtrace: CPU: 4 PID: 293 Comm: systemd-modules Not tainted 6.8.0-rc3_net_next_841a9b5 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x8a/0xa0 lockdep_rcu_suspicious+0x154/0x1a0 mlx5e_selq_apply+0x94/0xa0 [mlx5_core] mlx5e_selq_cleanup+0x3a/0x60 [mlx5_core] mlx5e_priv_init+0x2be/0x2f0 [mlx5_core] mlx5_rdma_setup_rn+0x7c/0x1a0 [mlx5_core] rdma_init_netdev+0x4e/0x80 [ib_core] ? mlx5_rdma_netdev_free+0x70/0x70 [mlx5_core] ipoib_intf_init+0x64/0x550 [ib_ipoib] ipoib_intf_alloc+0x4e/0xc0 [ib_ipoib] ipoib_add_one+0xb0/0x360 [ib_ipoib] add_client_context+0x112/0x1c0 [ib_core] ib_register_client+0x166/0x1b0 [ib_core] ? 0xffffffffa0573000 ipoib_init_module+0xeb/0x1a0 [ib_ipoib] do_one_initcall+0x61/0x250 do_init_module+0x8a/0x270 init_module_from_file+0x8b/0xd0 idempotent_init_module+0x17d/0x230 __x64_sys_finit_module+0x61/0xb0 do_syscall_64+0x71/0x140 entry_SYSCALL_64_after_hwframe+0x46/0x4e </TASK> | |||||
| CVE-2024-35957 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Fix WARN_ON in iommu probe path Commit 1a75cc710b95 ("iommu/vt-d: Use rbtree to track iommu probed devices") adds all devices probed by the iommu driver in a rbtree indexed by the source ID of each device. It assumes that each device has a unique source ID. This assumption is incorrect and the VT-d spec doesn't state this requirement either. The reason for using a rbtree to track devices is to look up the device with PCI bus and devfunc in the paths of handling ATS invalidation time out error and the PRI I/O page faults. Both are PCI ATS feature related. Only track the devices that have PCI ATS capabilities in the rbtree to avoid unnecessary WARN_ON in the iommu probe path. Otherwise, on some platforms below kernel splat will be displayed and the iommu probe results in failure. WARNING: CPU: 3 PID: 166 at drivers/iommu/intel/iommu.c:158 intel_iommu_probe_device+0x319/0xd90 Call Trace: <TASK> ? __warn+0x7e/0x180 ? intel_iommu_probe_device+0x319/0xd90 ? report_bug+0x1f8/0x200 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? intel_iommu_probe_device+0x319/0xd90 ? debug_mutex_init+0x37/0x50 __iommu_probe_device+0xf2/0x4f0 iommu_probe_device+0x22/0x70 iommu_bus_notifier+0x1e/0x40 notifier_call_chain+0x46/0x150 blocking_notifier_call_chain+0x42/0x60 bus_notify+0x2f/0x50 device_add+0x5ed/0x7e0 platform_device_add+0xf5/0x240 mfd_add_devices+0x3f9/0x500 ? preempt_count_add+0x4c/0xa0 ? up_write+0xa2/0x1b0 ? __debugfs_create_file+0xe3/0x150 intel_lpss_probe+0x49f/0x5b0 ? pci_conf1_write+0xa3/0xf0 intel_lpss_pci_probe+0xcf/0x110 [intel_lpss_pci] pci_device_probe+0x95/0x120 really_probe+0xd9/0x370 ? __pfx___driver_attach+0x10/0x10 __driver_probe_device+0x73/0x150 driver_probe_device+0x19/0xa0 __driver_attach+0xb6/0x180 ? __pfx___driver_attach+0x10/0x10 bus_for_each_dev+0x77/0xd0 bus_add_driver+0x114/0x210 driver_register+0x5b/0x110 ? __pfx_intel_lpss_pci_driver_init+0x10/0x10 [intel_lpss_pci] do_one_initcall+0x57/0x2b0 ? kmalloc_trace+0x21e/0x280 ? do_init_module+0x1e/0x210 do_init_module+0x5f/0x210 load_module+0x1d37/0x1fc0 ? init_module_from_file+0x86/0xd0 init_module_from_file+0x86/0xd0 idempotent_init_module+0x17c/0x230 __x64_sys_finit_module+0x56/0xb0 do_syscall_64+0x6e/0x140 entry_SYSCALL_64_after_hwframe+0x71/0x79 | |||||
| CVE-2024-35956 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: qgroup: fix qgroup prealloc rsv leak in subvolume operations Create subvolume, create snapshot and delete subvolume all use btrfs_subvolume_reserve_metadata() to reserve metadata for the changes done to the parent subvolume's fs tree, which cannot be mediated in the normal way via start_transaction. When quota groups (squota or qgroups) are enabled, this reserves qgroup metadata of type PREALLOC. Once the operation is associated to a transaction, we convert PREALLOC to PERTRANS, which gets cleared in bulk at the end of the transaction. However, the error paths of these three operations were not implementing this lifecycle correctly. They unconditionally converted the PREALLOC to PERTRANS in a generic cleanup step regardless of errors or whether the operation was fully associated to a transaction or not. This resulted in error paths occasionally converting this rsv to PERTRANS without calling record_root_in_trans successfully, which meant that unless that root got recorded in the transaction by some other thread, the end of the transaction would not free that root's PERTRANS, leaking it. Ultimately, this resulted in hitting a WARN in CONFIG_BTRFS_DEBUG builds at unmount for the leaked reservation. The fix is to ensure that every qgroup PREALLOC reservation observes the following properties: 1. any failure before record_root_in_trans is called successfully results in freeing the PREALLOC reservation. 2. after record_root_in_trans, we convert to PERTRANS, and now the transaction owns freeing the reservation. This patch enforces those properties on the three operations. Without it, generic/269 with squotas enabled at mkfs time would fail in ~5-10 runs on my system. With this patch, it ran successfully 1000 times in a row. | |||||
| CVE-2024-35955 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: kprobes: Fix possible use-after-free issue on kprobe registration When unloading a module, its state is changing MODULE_STATE_LIVE -> MODULE_STATE_GOING -> MODULE_STATE_UNFORMED. Each change will take a time. `is_module_text_address()` and `__module_text_address()` works with MODULE_STATE_LIVE and MODULE_STATE_GOING. If we use `is_module_text_address()` and `__module_text_address()` separately, there is a chance that the first one is succeeded but the next one is failed because module->state becomes MODULE_STATE_UNFORMED between those operations. In `check_kprobe_address_safe()`, if the second `__module_text_address()` is failed, that is ignored because it expected a kernel_text address. But it may have failed simply because module->state has been changed to MODULE_STATE_UNFORMED. In this case, arm_kprobe() will try to modify non-exist module text address (use-after-free). To fix this problem, we should not use separated `is_module_text_address()` and `__module_text_address()`, but use only `__module_text_address()` once and do `try_module_get(module)` which is only available with MODULE_STATE_LIVE. | |||||
| CVE-2024-35953 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix deadlock in context_xa ivpu_device->context_xa is locked both in kernel thread and IRQ context. It requires XA_FLAGS_LOCK_IRQ flag to be passed during initialization otherwise the lock could be acquired from a thread and interrupted by an IRQ that locks it for the second time causing the deadlock. This deadlock was reported by lockdep and observed in internal tests. | |||||
| CVE-2024-35952 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/ast: Fix soft lockup There is a while-loop in ast_dp_set_on_off() that could lead to infinite-loop. This is because the register, VGACRI-Dx, checked in this API is a scratch register actually controlled by a MCU, named DPMCU, in BMC. These scratch registers are protected by scu-lock. If suc-lock is not off, DPMCU can not update these registers and then host will have soft lockup due to never updated status. DPMCU is used to control DP and relative registers to handshake with host's VGA driver. Even the most time-consuming task, DP's link training, is less than 100ms. 200ms should be enough. | |||||