Total
398493 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2025-38633 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: clk: spacemit: mark K1 pll1_d8 as critical The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks, including those used by APB and AXI buses. Guodong Xu discovered that this clock got disabled while responding to getting -EPROBE_DEFER when requesting a reset controller. The needed clock (CLK_DMA, along with its parents) had already been enabled. To respond to the probe deferral return, the CLK_DMA clock was disabled, and this led to parent clocks also reducing their enable count. When the enable count for pll1_d8 was decremented it became 0, which caused it to be disabled. This led to a system hang. Marking that clock critical resolves this by preventing it from being disabled. Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to be supplied for a CCU_FACTOR_GATE clock. | |||||
| CVE-2025-38632 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 4.7 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: pinmux: fix race causing mux_owner NULL with active mux_usecount commit 5a3e85c3c397 ("pinmux: Use sequential access to access desc->pinmux data") tried to address the issue when two client of the same gpio calls pinctrl_select_state() for the same functionality, was resulting in NULL pointer issue while accessing desc->mux_owner. However, issue was not completely fixed due to the way it was handled and it can still result in the same NULL pointer. The issue occurs due to the following interleaving: cpu0 (process A) cpu1 (process B) pin_request() { pin_free() { mutex_lock() desc->mux_usecount--; //becomes 0 .. mutex_unlock() mutex_lock(desc->mux) desc->mux_usecount++; // becomes 1 desc->mux_owner = owner; mutex_unlock(desc->mux) mutex_lock(desc->mux) desc->mux_owner = NULL; mutex_unlock(desc->mux) This sequence leads to a state where the pin appears to be in use (`mux_usecount == 1`) but has no owner (`mux_owner == NULL`), which can cause NULL pointer on next pin_request on the same pin. Ensure that updates to mux_usecount and mux_owner are performed atomically under the same lock. Only clear mux_owner when mux_usecount reaches zero and no new owner has been assigned. | |||||
| CVE-2025-38631 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: clk: imx95-blk-ctl: Fix synchronous abort When enabling runtime PM for clock suppliers that also belong to a power domain, the following crash is thrown: error: synchronous external abort: 0000000096000010 [#1] PREEMPT SMP Workqueue: events_unbound deferred_probe_work_func pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : clk_mux_get_parent+0x60/0x90 lr : clk_core_reparent_orphans_nolock+0x58/0xd8 Call trace: clk_mux_get_parent+0x60/0x90 clk_core_reparent_orphans_nolock+0x58/0xd8 of_clk_add_hw_provider.part.0+0x90/0x100 of_clk_add_hw_provider+0x1c/0x38 imx95_bc_probe+0x2e0/0x3f0 platform_probe+0x70/0xd8 Enabling runtime PM without explicitly resuming the device caused the power domain cut off after clk_register() is called. As a result, a crash happens when the clock hardware provider is added and attempts to access the BLK_CTL register. Fix this by using devm_pm_runtime_enable() instead of pm_runtime_enable() and getting rid of the pm_runtime_disable() in the cleanup path. | |||||
| CVE-2025-38630 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: fbdev: imxfb: Check fb_add_videomode to prevent null-ptr-deref fb_add_videomode() can fail with -ENOMEM when its internal kmalloc() cannot allocate a struct fb_modelist. If that happens, the modelist stays empty but the driver continues to register. Add a check for its return value to prevent poteintial null-ptr-deref, which is similar to the commit 17186f1f90d3 ("fbdev: Fix do_register_framebuffer to prevent null-ptr-deref in fb_videomode_to_var"). | |||||
| CVE-2025-38629 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: usb: scarlett2: Fix missing NULL check scarlett2_input_select_ctl_info() sets up the string arrays allocated via kasprintf(), but it misses NULL checks, which may lead to NULL dereference Oops. Let's add the proper NULL check. | |||||
| CVE-2025-38628 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: vdpa/mlx5: Fix release of uninitialized resources on error path The commit in the fixes tag made sure that mlx5_vdpa_free() is the single entrypoint for removing the vdpa device resources added in mlx5_vdpa_dev_add(), even in the cleanup path of mlx5_vdpa_dev_add(). This means that all functions from mlx5_vdpa_free() should be able to handle uninitialized resources. This was not the case though: mlx5_vdpa_destroy_mr_resources() and mlx5_cmd_cleanup_async_ctx() were not able to do so. This caused the splat below when adding a vdpa device without a MAC address. This patch fixes these remaining issues: - Makes mlx5_vdpa_destroy_mr_resources() return early if called on uninitialized resources. - Moves mlx5_cmd_init_async_ctx() early on during device addition because it can't fail. This means that mlx5_cmd_cleanup_async_ctx() also can't fail. To mirror this, move the call site of mlx5_cmd_cleanup_async_ctx() in mlx5_vdpa_free(). An additional comment was added in mlx5_vdpa_free() to document the expectations of functions called from this context. Splat: mlx5_core 0000:b5:03.2: mlx5_vdpa_dev_add:3950:(pid 2306) warning: No mac address provisioned? ------------[ cut here ]------------ WARNING: CPU: 13 PID: 2306 at kernel/workqueue.c:4207 __flush_work+0x9a/0xb0 [...] Call Trace: <TASK> ? __try_to_del_timer_sync+0x61/0x90 ? __timer_delete_sync+0x2b/0x40 mlx5_vdpa_destroy_mr_resources+0x1c/0x40 [mlx5_vdpa] mlx5_vdpa_free+0x45/0x160 [mlx5_vdpa] vdpa_release_dev+0x1e/0x50 [vdpa] device_release+0x31/0x90 kobject_cleanup+0x37/0x130 mlx5_vdpa_dev_add+0x327/0x890 [mlx5_vdpa] vdpa_nl_cmd_dev_add_set_doit+0x2c1/0x4d0 [vdpa] genl_family_rcv_msg_doit+0xd8/0x130 genl_family_rcv_msg+0x14b/0x220 ? __pfx_vdpa_nl_cmd_dev_add_set_doit+0x10/0x10 [vdpa] genl_rcv_msg+0x47/0xa0 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x53/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x27b/0x3b0 netlink_sendmsg+0x1f7/0x430 __sys_sendto+0x1fa/0x210 ? ___pte_offset_map+0x17/0x160 ? next_uptodate_folio+0x85/0x2b0 ? percpu_counter_add_batch+0x51/0x90 ? filemap_map_pages+0x515/0x660 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x7b/0x2c0 ? do_read_fault+0x108/0x220 ? do_pte_missing+0x14a/0x3e0 ? __handle_mm_fault+0x321/0x730 ? count_memcg_events+0x13f/0x180 ? handle_mm_fault+0x1fb/0x2d0 ? do_user_addr_fault+0x20c/0x700 ? syscall_exit_work+0x104/0x140 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f0c25b0feca [...] ---[ end trace 0000000000000000 ]--- | |||||
| CVE-2025-38626 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to trigger foreground gc during f2fs_map_blocks() in lfs mode w/ "mode=lfs" mount option, generic/299 will cause system panic as below: ------------[ cut here ]------------ kernel BUG at fs/f2fs/segment.c:2835! Call Trace: <TASK> f2fs_allocate_data_block+0x6f4/0xc50 f2fs_map_blocks+0x970/0x1550 f2fs_iomap_begin+0xb2/0x1e0 iomap_iter+0x1d6/0x430 __iomap_dio_rw+0x208/0x9a0 f2fs_file_write_iter+0x6b3/0xfa0 aio_write+0x15d/0x2e0 io_submit_one+0x55e/0xab0 __x64_sys_io_submit+0xa5/0x230 do_syscall_64+0x84/0x2f0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0010:new_curseg+0x70f/0x720 The root cause of we run out-of-space is: in f2fs_map_blocks(), f2fs may trigger foreground gc only if it allocates any physical block, it will be a little bit later when there is multiple threads writing data w/ aio/dio/bufio method in parallel, since we always use OPU in lfs mode, so f2fs_map_blocks() does block allocations aggressively. In order to fix this issue, let's give a chance to trigger foreground gc in prior to block allocation in f2fs_map_blocks(). | |||||
| CVE-2025-38625 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: vfio/pds: Fix missing detach_ioas op When CONFIG_IOMMUFD is enabled and a device is bound to the pds_vfio_pci driver, the following WARN_ON() trace is seen and probe fails: WARNING: CPU: 0 PID: 5040 at drivers/vfio/vfio_main.c:317 __vfio_register_dev+0x130/0x140 [vfio] <...> pds_vfio_pci 0000:08:00.1: probe with driver pds_vfio_pci failed with error -22 This is because the driver's vfio_device_ops.detach_ioas isn't set. Fix this by using the generic vfio_iommufd_physical_detach_ioas function. | |||||
| CVE-2025-38624 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: PCI: pnv_php: Clean up allocated IRQs on unplug When the root of a nested PCIe bridge configuration is unplugged, the pnv_php driver leaked the allocated IRQ resources for the child bridges' hotplug event notifications, resulting in a panic. Fix this by walking all child buses and deallocating all its IRQ resources before calling pci_hp_remove_devices(). Also modify the lifetime of the workqueue at struct pnv_php_slot::wq so that it is only destroyed in pnv_php_free_slot(), instead of pnv_php_disable_irq(). This is required since pnv_php_disable_irq() will now be called by workers triggered by hot unplug interrupts, so the workqueue needs to stay allocated. The abridged kernel panic that occurs without this patch is as follows: WARNING: CPU: 0 PID: 687 at kernel/irq/msi.c:292 msi_device_data_release+0x6c/0x9c CPU: 0 UID: 0 PID: 687 Comm: bash Not tainted 6.14.0-rc5+ #2 Call Trace: msi_device_data_release+0x34/0x9c (unreliable) release_nodes+0x64/0x13c devres_release_all+0xc0/0x140 device_del+0x2d4/0x46c pci_destroy_dev+0x5c/0x194 pci_hp_remove_devices+0x90/0x128 pci_hp_remove_devices+0x44/0x128 pnv_php_disable_slot+0x54/0xd4 power_write_file+0xf8/0x18c pci_slot_attr_store+0x40/0x5c sysfs_kf_write+0x64/0x78 kernfs_fop_write_iter+0x1b0/0x290 vfs_write+0x3bc/0x50c ksys_write+0x84/0x140 system_call_exception+0x124/0x230 system_call_vectored_common+0x15c/0x2ec [bhelgaas: tidy comments] | |||||
| CVE-2025-38623 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: PCI: pnv_php: Fix surprise plug detection and recovery The existing PowerNV hotplug code did not handle surprise plug events correctly, leading to a complete failure of the hotplug system after device removal and a required reboot to detect new devices. This comes down to two issues: 1) When a device is surprise removed, often the bridge upstream port will cause a PE freeze on the PHB. If this freeze is not cleared, the MSI interrupts from the bridge hotplug notification logic will not be received by the kernel, stalling all plug events on all slots associated with the PE. 2) When a device is removed from a slot, regardless of surprise or programmatic removal, the associated PHB/PE ls left frozen. If this freeze is not cleared via a fundamental reset, skiboot is unable to clear the freeze and cannot retrain / rescan the slot. This also requires a reboot to clear the freeze and redetect the device in the slot. Issue the appropriate unfreeze and rescan commands on hotplug events, and don't oops on hotplug if pci_bus_to_OF_node() returns NULL. [bhelgaas: tidy comments] | |||||
| CVE-2025-38622 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: drop UFO packets in udp_rcv_segment() When sending a packet with virtio_net_hdr to tun device, if the gso_type in virtio_net_hdr is SKB_GSO_UDP and the gso_size is less than udphdr size, below crash may happen. ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:4572! Oops: invalid opcode: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 62 Comm: mytest Not tainted 6.16.0-rc7 #203 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:skb_pull_rcsum+0x8e/0xa0 Code: 00 00 5b c3 cc cc cc cc 8b 93 88 00 00 00 f7 da e8 37 44 38 00 f7 d8 89 83 88 00 00 00 48 8b 83 c8 00 00 00 5b c3 cc cc cc cc <0f> 0b 0f 0b 66 66 2e 0f 1f 84 00 000 RSP: 0018:ffffc900001fba38 EFLAGS: 00000297 RAX: 0000000000000004 RBX: ffff8880040c1000 RCX: ffffc900001fb948 RDX: ffff888003e6d700 RSI: 0000000000000008 RDI: ffff88800411a062 RBP: ffff8880040c1000 R08: 0000000000000000 R09: 0000000000000001 R10: ffff888003606c00 R11: 0000000000000001 R12: 0000000000000000 R13: ffff888004060900 R14: ffff888004050000 R15: ffff888004060900 FS: 000000002406d3c0(0000) GS:ffff888084a19000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000040 CR3: 0000000004007000 CR4: 00000000000006f0 Call Trace: <TASK> udp_queue_rcv_one_skb+0x176/0x4b0 net/ipv4/udp.c:2445 udp_queue_rcv_skb+0x155/0x1f0 net/ipv4/udp.c:2475 udp_unicast_rcv_skb+0x71/0x90 net/ipv4/udp.c:2626 __udp4_lib_rcv+0x433/0xb00 net/ipv4/udp.c:2690 ip_protocol_deliver_rcu+0xa6/0x160 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x72/0x90 net/ipv4/ip_input.c:233 ip_sublist_rcv_finish+0x5f/0x70 net/ipv4/ip_input.c:579 ip_sublist_rcv+0x122/0x1b0 net/ipv4/ip_input.c:636 ip_list_rcv+0xf7/0x130 net/ipv4/ip_input.c:670 __netif_receive_skb_list_core+0x21d/0x240 net/core/dev.c:6067 netif_receive_skb_list_internal+0x186/0x2b0 net/core/dev.c:6210 napi_complete_done+0x78/0x180 net/core/dev.c:6580 tun_get_user+0xa63/0x1120 drivers/net/tun.c:1909 tun_chr_write_iter+0x65/0xb0 drivers/net/tun.c:1984 vfs_write+0x300/0x420 fs/read_write.c:593 ksys_write+0x60/0xd0 fs/read_write.c:686 do_syscall_64+0x50/0x1c0 arch/x86/entry/syscall_64.c:63 </TASK> To trigger gso segment in udp_queue_rcv_skb(), we should also set option UDP_ENCAP_ESPINUDP to enable udp_sk(sk)->encap_rcv. When the encap_rcv hook return 1 in udp_queue_rcv_one_skb(), udp_csum_pull_header() will try to pull udphdr, but the skb size has been segmented to gso size, which leads to this crash. Previous commit cf329aa42b66 ("udp: cope with UDP GRO packet misdirection") introduces segmentation in UDP receive path only for GRO, which was never intended to be used for UFO, so drop UFO packets in udp_rcv_segment(). | |||||
| CVE-2025-38620 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: zloop: fix KASAN use-after-free of tag set When a zoned loop device, or zloop device, is removed, KASAN enabled kernel reports "BUG KASAN use-after-free" in blk_mq_free_tag_set(). The BUG happens because zloop_ctl_remove() calls put_disk(), which invokes zloop_free_disk(). The zloop_free_disk() frees the memory allocated for the zlo pointer. However, after the memory is freed, zloop_ctl_remove() calls blk_mq_free_tag_set(&zlo->tag_set), which accesses the freed zlo. Hence the KASAN use-after-free. zloop_ctl_remove() put_disk(zlo->disk) put_device() kobject_put() ... zloop_free_disk() kvfree(zlo) blk_mq_free_tag_set(&zlo->tag_set) To avoid the BUG, move the call to blk_mq_free_tag_set(&zlo->tag_set) from zloop_ctl_remove() into zloop_free_disk(). This ensures that the tag_set is freed before the call to kvfree(zlo). | |||||
| CVE-2025-38613 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: staging: gpib: fix unset padding field copy back to userspace The introduction of a padding field in the gpib_board_info_ioctl is showing up as initialized data on the stack frame being copyied back to userspace in function board_info_ioctl. The simplest fix is to initialize the entire struct to zero to ensure all unassigned padding fields are zero'd before being copied back to userspace. | |||||
| CVE-2025-38612 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: staging: fbtft: fix potential memory leak in fbtft_framebuffer_alloc() In the error paths after fb_info structure is successfully allocated, the memory allocated in fb_deferred_io_init() for info->pagerefs is not freed. Fix that by adding the cleanup function on the error path. | |||||
| CVE-2025-38610 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: powercap: dtpm_cpu: Fix NULL pointer dereference in get_pd_power_uw() The get_pd_power_uw() function can crash with a NULL pointer dereference when em_cpu_get() returns NULL. This occurs when a CPU becomes impossible during runtime, causing get_cpu_device() to return NULL, which propagates through em_cpu_get() and leads to a crash when em_span_cpus() dereferences the NULL pointer. Add a NULL check after em_cpu_get() and return 0 if unavailable, matching the existing fallback behavior in __dtpm_cpu_setup(). [ rjw: Drop an excess empty code line ] | |||||
| CVE-2025-38609 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: PM / devfreq: Check governor before using governor->name Commit 96ffcdf239de ("PM / devfreq: Remove redundant governor_name from struct devfreq") removes governor_name and uses governor->name to replace it. But devfreq->governor may be NULL and directly using devfreq->governor->name may cause null pointer exception. Move the check of governor to before using governor->name. | |||||
| CVE-2025-38606 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Avoid accessing uninitialized arvif->ar during beacon miss During beacon miss handling, ath12k driver iterates over active virtual interfaces (vifs) and attempts to access the radio object (ar) via arvif->deflink->ar. However, after commit aa80f12f3bed ("wifi: ath12k: defer vdev creation for MLO"), arvif is linked to a radio only after vdev creation, typically when a channel is assigned or a scan is requested. For P2P capable devices, a default P2P interface is created by wpa_supplicant along with regular station interfaces, these serve as dummy interfaces for P2P-capable stations, lack an associated netdev and initiate frequent scans to discover neighbor p2p devices. When a scan is initiated on such P2P vifs, driver selects destination radio (ar) based on scan frequency, creates a scan vdev, and attaches arvif to the radio. Once the scan completes or is aborted, the scan vdev is deleted, detaching arvif from the radio and leaving arvif->ar uninitialized. While handling beacon miss for station interfaces, P2P interface is also encountered in the vif iteration and ath12k_mac_handle_beacon_miss_iter() tries to dereference the uninitialized arvif->deflink->ar. Fix this by verifying that vdev is created for the arvif before accessing its ar during beacon miss handling and similar vif iterator callbacks. ========================================================================== wlp6s0: detected beacon loss from AP (missed 7 beacons) - probing KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 5 UID: 0 PID: 0 Comm: swapper/5 Not tainted 6.16.0-rc1-wt-ath+ #2 PREEMPT(full) RIP: 0010:ath12k_mac_handle_beacon_miss_iter+0xb5/0x1a0 [ath12k] Call Trace: __iterate_interfaces+0x11a/0x410 [mac80211] ieee80211_iterate_active_interfaces_atomic+0x61/0x140 [mac80211] ath12k_mac_handle_beacon_miss+0xa1/0xf0 [ath12k] ath12k_roam_event+0x393/0x560 [ath12k] ath12k_wmi_op_rx+0x1486/0x28c0 [ath12k] ath12k_htc_process_trailer.isra.0+0x2fb/0x620 [ath12k] ath12k_htc_rx_completion_handler+0x448/0x830 [ath12k] ath12k_ce_recv_process_cb+0x549/0x9e0 [ath12k] ath12k_ce_per_engine_service+0xbe/0xf0 [ath12k] ath12k_pci_ce_workqueue+0x69/0x120 [ath12k] process_one_work+0xe3a/0x1430 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 | |||||
| CVE-2025-38605 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Pass ab pointer directly to ath12k_dp_tx_get_encap_type() In ath12k_dp_tx_get_encap_type(), the arvif parameter is only used to retrieve the ab pointer. In vdev delete sequence the arvif->ar could become NULL and that would trigger kernel panic. Since the caller ath12k_dp_tx() already has a valid ab pointer, pass it directly to avoid panic and unnecessary dereferencing. PC points to "ath12k_dp_tx+0x228/0x988 [ath12k]" LR points to "ath12k_dp_tx+0xc8/0x988 [ath12k]". The Backtrace obtained is as follows: ath12k_dp_tx+0x228/0x988 [ath12k] ath12k_mac_tx_check_max_limit+0x608/0x920 [ath12k] ieee80211_process_measurement_req+0x320/0x348 [mac80211] ieee80211_tx_dequeue+0x9ac/0x1518 [mac80211] ieee80211_tx_dequeue+0xb14/0x1518 [mac80211] ieee80211_tx_prepare_skb+0x224/0x254 [mac80211] ieee80211_xmit+0xec/0x100 [mac80211] __ieee80211_subif_start_xmit+0xc50/0xf40 [mac80211] ieee80211_subif_start_xmit+0x2e8/0x308 [mac80211] netdev_start_xmit+0x150/0x18c dev_hard_start_xmit+0x74/0xc0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 | |||||
| CVE-2025-38602 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: iwlwifi: Add missing check for alloc_ordered_workqueue Add check for the return value of alloc_ordered_workqueue since it may return NULL pointer. | |||||
| CVE-2025-38597 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/rockchip: vop2: fail cleanly if missing a primary plane for a video-port Each window of a vop2 is usable by a specific set of video ports, so while binding the vop2, we look through the list of available windows trying to find one designated as primary-plane and usable by that specific port. The code later wants to use drm_crtc_init_with_planes with that found primary plane, but nothing has checked so far if a primary plane was actually found. For whatever reason, the rk3576 vp2 does not have a usable primary window (if vp0 is also in use) which brought the issue to light and ended in a null-pointer dereference further down. As we expect a primary-plane to exist for a video-port, add a check at the end of the window-iteration and fail probing if none was found. | |||||