Total
396088 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2026-89766 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: pidfd: hold exec_update_lock around namespace ioctl The PIDFD_GET_*_NAMESPACE ioctls in pidfd_ioctl() perform a filesystem credentials ptrace access check before handing out a namespace file descriptor. The accompanying comment states that the code "mirrors nsfs behavior", but, unlike the corresponding procfs paths, it does so without holding the target task's exec_update_lock. proc_ns_get_link() and proc_ns_readlink() both take exec_update_lock for reading around the ptrace check and the namespace lookup, so that the credentials used for the access decision match those of the task when its namespace is read. Without it, a caller can pass the check against the target's old credentials and then read the namespace after the target has execve()'d a setuid binary and committed new credentials -- accessing namespace information it should have been denied. Hold exec_update_lock for reading around the ptrace check and the namespace lookup so that pidfd truly mirrors nsfs behavior, as the comment already claims. open_namespace() itself runs outside the lock: once a namespace reference is obtained it carries its own refcount and is opened with the caller's own credentials, so a concurrent execve() on the target can no longer affect the outcome. | |||||
| CVE-2026-89759 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: mm/kmemleak: avoid soft lockup when scanning task stacks Patch series "mm/kmemleak: avoid soft lockup when scanning task", v3. kmemleak_scan() scans every task stack under one rcu_read_lock() with no reschedule point, which can trip the soft lockup watchdog on hosts with very many threads. That prints the following message, depending on the workload+host configuration: watchdog: BUG: soft lockup - CPU#35 stuck for 22s! [kmemleak:537] scan_block kmemleak_scan kmemleak_scan_thread kthread Patch 1 walks the tasks with find_ge_pid() so the scan reschedules between tasks Patches 2-3 let the scan loops stop early once a scan is interrupted. This patch (of 3): kmemleak_scan() walks every thread and scans its kernel stack under a single rcu_read_lock() with no reschedule point. On a host with very many threads -- amplified by KASAN/lockdep in debug builds -- this loop can hog a CPU long enough to trip the soft lockup watchdog: watchdog: BUG: soft lockup - CPU#35 stuck for 22s! [kmemleak:537] scan_block kmemleak_scan kmemleak_scan_thread kthread A cond_resched() cannot be added directly: the loop runs inside an RCU read-side critical section. Walk the tasks one PID at a time with find_ge_pid(), taking the RCU read lock only to look up and pin each task. The stack is then scanned with no lock held, so cond_resched() runs between tasks and the scan stops early on scan_should_stop(). This follows the next_tgid()/task_seq_get_next() iteration pattern and keeps each RCU critical section short. | |||||
| CVE-2026-89757 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: mm/mglru: fix and remove redundant unevictable folio handling sort_folio() has a shortcut for moving folios that are no longer evictable but are still sitting on a generation list. However, this shortcut is buggy. It does not follow the PG_lru usage convention, and it has a more serious issue. Unevictable folios are not threaded on lists[LRU_UNEVICTABLE], so that folio->lru can be reused to hold folio->mlock_count (see the comment in lruvec_init()). Hence lruvec_add_folio() skips the list_add() for them, and every other place that turns a folio unevictable initialises mlock_count explicitly: lru_add() sets it to 0, __mlock_folio() and __mlock_new_folio() set it to !!folio_test_mlocked(folio). sort_folio() sets nothing, and the lru_gen_del_folio() right above it may have already poisoned folio->lru via list_del(), so mlock_count ends up aliasing LIST_POISON2, which reads as 0x122, i.e. 290. The result is user visible. On munlock, __munlock_folio() decrements that bogus count, finds it still non-zero and bails out before clearing PG_mlocked, so the folio remains unevictable and the Mlocked accounting stays inflated until the folio is freed. The shortcut also touches the LRU flags in the wrong order. It calls lru_gen_del_folio() while PG_lru is still set, so a concurrent folio_test_clear_lru() (e.g. compaction, folio_isolate_lru()) can succeed on a folio that has already been taken off the generation list, which may lead to unexpected behavior. So fix it by isolating them as common folios and letting the generic shrink path cull them. This matches the classical LRU behavior, and there should be no visible effect on the generic eviction or isolation behavior. There is no performance concern either, such a folio goes through this once, and then it is off the generation lists for good. | |||||
| CVE-2026-89745 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: debugfs: Fix lockdown check for mmap_prepare Commit 651fdda8406d ("relay: update relay to use mmap_prepare") changed the `mmap` file operation to `mmap_prepare` for relayfs, but the lockdown check in debugfs was not updated accordingly. This prevents debugfs from being locked down when the kernel is in integrity mode if a file uses `mmap_prepare` but not `mmap`. Since the conversion to `mmap_prepare` across the kernel is not yet complete, update the lockdown check to look for both `mmap` and `mmap_prepare` to ensure comprehensive coverage. | |||||
| CVE-2026-89740 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: serial: imx: serialize imx_uart_ports[] lifetime imx_uart_probe() publishes its devm-allocated port in imx_uart_ports[] before uart_add_one_port() because console setup uses the table. The entry is not cleared when adding the port fails or after removal, leaving a dangling pointer. A sibling probe can register the shared console through that stale entry. This was reproduced under KASAN on QEMU mcimx6ul-evk by unbinding a sibling UART, unbinding the console UART and rebinding the sibling. Keep the entry valid through uart_remove_one_port(), then clear it. Protect port addition and removal together with their table updates so sibling operations cannot interleave. Reject an occupied slot rather than clobbering an active port during a duplicate-line probe. | |||||
| CVE-2026-89739 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: gadget: Fix use-after-free in dwc3_gadget_free_endpoints due to race condition In dwc3_gadget_init_endpoint, &dep->nostream_work is bound with dwc3_nostream_work, and dwc3_gadget_endpoint_stream_event can queue this delayed work on system_percpu_wq when a DEPEVT_STREAM_NOSTREAM event is received. If we remove the gadget, dwc3_gadget_free_endpoints makes cleanup and the memory allocated for dep with kzalloc() is released by kfree(dep), while the delayed work mentioned above may still be pending or running. The sequence of operations that may lead to a UAF bug is as follows: CPU0 CPU1 | dwc3_thread_interrupt | dwc3_endpoint_interrupt | dwc3_gadget_endpoint_stream_event | queue_delayed_work(system_percpu_wq, | &dep->nostream_work) dwc3_gadget_free_endpoints | dwc3_free_trb_pool(dep) | list_del(&dep->endpoint.ep_list) | dwc3_debugfs_remove_endpoint_dir(dep) | kfree(dep) | // dep is freed | | dwc3_nostream_work | // use dep (use-after-free) Fix it by canceling the delayed work before kfree(dep) in dwc3_gadget_free_endpoints. | |||||
| CVE-2026-89737 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: usb: typec: thunderbolt: Disable work before freeing tbt on remove tbt_altmode_remove() drops the plug and cable references without draining tbt->work. The work function dereferences those references, and can also requeue itself in its error path. The VDM callbacks can queue the same work item. Disable and drain tbt->work before dropping the references. This waits for an existing invocation and prevents subsequent schedule_work() calls from queueing it during teardown. This issue was found by an in-house static analysis tool and confirmed by manual code review. | |||||
| CVE-2026-89734 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: usb: gadget: uvc: Fix null pointer dereference in uvcg_video_init() In uvcg_video_init(), if kthread_run_worker() fails, the error logged uses uvcg_err(), however, the pointer it uses: video->uvc is not assigned at this point, triggering a null pointer dereference. Fix this by directly using uvc->func which is assigned already. | |||||
| CVE-2026-89728 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: i3c: renesas: Fix out-of-bounds access for newdevs mask When software initiates DAA (Dynamic Address Assignment), the controller reports the result via the NRSPQP (Normal Response Queue Port Register). The data length field of the response descriptor, which is accessible through the NRSPQP register, indicates the number of devices remaining after DAA. Consequently, when the bus is empty, this field contains the maximum number of devices supported by the controller (8 for the Renesas I3C controller). Adjust the condition that computes the newly discovered devices bitmask to prevent an out-of-bounds when the I3C bus is empty. | |||||
| CVE-2026-89727 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: GICv2: Don't WARN on out-of-range GICV_DIR INTID vgic_v2_deactivate() passes the INTID a guest wrote to GICV_DIR straight to vgic_get_vcpu_irq(), and treats a failed lookup as a "can't happen" condition with WARN_ON_ONCE(). The guest can make it happen at will, though: for any INTID outside of the implemented SGI, PPI and SPI ranges the lookup returns NULL, since GICv2 has no LPIs. A guest running with EOImode==1 writing such an INTID to GICV_DIR triggers the WARN, and panics hosts running with panic_on_warn. Drop the WARN and ignore failed lookups. | |||||
| CVE-2026-89721 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: phy: rockchip-samsung-dcphy: fix out-of-range max_register The PHY register block is 64KB, so with a register stride of 4 the last accessible register sits at offset 0xfffc. max_register names 0x10000, one register past the end of the mapping: dumping the registers through the regmap debugfs interface reads beyond the ioremapped region and oopses on the unmapped page. The oops fires with the regmap lock held, so later PHY operations deadlock. | |||||
| CVE-2026-89716 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: zram: validate deflate params We must validate user-supplied deflate winbits before we pass it to zlib_deflate_workspacesize(), which triggers BUG_ON() if winbits value is outside of valid ranges. | |||||
| CVE-2026-89715 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: NFS/localio: fix ref leak on nfs_uuid_add_file failure When nfs_uuid_add_file() races with nfs_uuid_put() tearing down uuid->net, it returns -ENXIO without publishing nfl->nfs_uuid via rcu_assign_pointer(). nfs_open_local_fh() then enters its error branch and only releases the slot's file ref and its paired net ref plus its own entry-time net ref, while the close path is a no-op: nfs_close_local_fh() nfs_uuid = rcu_dereference(nfl->nfs_uuid); if (!nfs_uuid) { rcu_read_unlock(); return; } /* always */ nfsd_open_local_fh() returns localio holding a caller-owned +1 nfsd_file reference (from nfsd_file_get() after nfsd_file_acquire_local()) and an entry-time nfsd_net reference (from its first nfsd_net_try_get()) embedded as nf->nf_net. Both are leaked on the failure path, pinning one nfsd_file (and the underlying struct file, dentry, inode) and one nfsd_net_ref per occurrence, which blocks nfsd_net and netns teardown. Fix by releasing the caller-owned file ref and its net ref through the existing helper, using a stack-local RCU pointer so the helper can xchg it out, then returning -ENXIO so callers do not dereference a localio whose slot has been cleared: struct nfsd_file __rcu *tmp = RCU_INITIALIZER(localio); nfs_to_nfsd_file_put_local(pnf); nfs_to_nfsd_file_put_local(&tmp); localio = ERR_PTR(-ENXIO); The trailing nfs_to_nfsd_net_put(net) continues to release the outer net ref, so all three nfsd_net_try_get() increments are balanced on the error branch. | |||||
| CVE-2026-89714 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: NFS: fix delegation_hash_table leak when nfs4_server_common_setup() fails nfs4_server_common_setup() allocates server->delegation_hash_table first, but server->destroy - the only path that frees the table via nfs4_destroy_server() - is not assigned until the very end of the function. If any intermediate step fails (the is_ds_only_client() check, nfs4_init_session(), nfs4_get_rootfh(), or nfs_probe_server()), the function returns with server->destroy still NULL, so the caller's nfs_free_server() skips the destroy callback and the hash table is leaked (4 KiB per attempt with the default delegation watermark). This is trivially reachable from userspace: every failed NFSv4 mount leaks one allocation. A client that persistently retries a mount that cannot succeed leaks kernel memory without bound. Observed in production where a Longhorn backup poller retried mount.nfs4 against an NFSv3-only server roughly 10 times per second, leaking ~3.4 GiB of unreclaimable slab (kmalloc-rnd-13-4k) per day; the node accumulated 12 GiB of leaked slab before the source was identified via the kmem:kmalloc tracepoint (call_site=nfs4_delegation_hash_alloc). Reproducer: # server exports NFSv3 only (or export path absent for v4) while :; do mount -t nfs4 <server>:/missing /mnt; done # watch SUnreclaim in /proc/meminfo grow 4 KiB per iteration Free the table on the error paths between the allocation and the assignment of server->destroy. | |||||
| CVE-2026-89701 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: nfsd: validate nseconds in TIME_DELEG decode paths The xdrgen-based TIME_DELEG_ACCESS and TIME_DELEG_MODIFY decode arms store a raw uint32_t nseconds directly into tv_nsec without enforcing nseconds < NSEC_PER_SEC. The legacy nfsd4_decode_nfstime4 has this check but the TIME_DELEG paths do not. A malformed timespec can propagate through notify_change() to disk. Add range checks in both nfs4xdr.c (SETATTR path) and nfs4callback.c (CB_GETATTR path). | |||||
| CVE-2026-89683 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: nfsd: fix dentry ref leak on V4ROOT export filehandle lookup nfsd_set_fh_dentry() leaks the dentry reference from exportfs_decode_fh_raw() when the NFS3_FHSIZE or NFS_FHSIZE switch cases detect NFSEXP_V4ROOT and goto out. The out: label calls exp_put() but never dput(dentry), and fhp->fh_dentry was never assigned so fh_put() cannot compensate. A crafted NFSv3 filehandle targeting a V4ROOT export's fsid triggers the leak on every request. | |||||
| CVE-2026-89666 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: nfsd: reject out-of-range nseconds in NFSv3 SETATTR and create ops A client can send an NFSv3 SETATTR, CREATE, MKDIR, SYMLINK or MKNOD carrying an atime or mtime whose nseconds field is out of range. The value is well-formed on the wire and decodes cleanly into a valid uint32, but it is not a valid timespec64: tv_nsec must be less than NSEC_PER_SEC. Nothing in the setattr path clamps it. notify_change() runs the time through timestamp_truncate(), which does not reduce tv_nsec below NSEC_PER_SEC when the filesystem supports nanosecond granularity (s_time_gran == 1), and the inode atime/mtime setters store it verbatim (only ctime is normalized, via inode_set_ctime_to_ts()). The un-normalized value then corrupts on-disk metadata: ext4's ext4_encode_extra_time() shifts tv_nsec left by EXT4_EPOCH_BITS, which overflows the 32-bit extra field and clobbers the seconds-epoch bits, so the stored seconds (and thus the year) are wrong on read-back. XFS with bigtime mis-stores the timestamp for the same reason. Validate the client-supplied atime/mtime in the proc handlers and return NFS3ERR_INVAL before anything is changed. RFC 1813 lists NFS3ERR_INVAL for SETATTR and describes it as the error for a value the server 'can not store ... in its own representation'; the client maps it to EINVAL. Checking in the proc handlers, rather than in nfsd_setattr(), keeps the rejection in front of object creation. The create operations create the object before nfsd_create_setattr() runs, so a late failure would leave the new object behind and turn a non-idempotent request into a namespace change that reports failure. The check is therefore done up front, for the create operations before the object is created. tv_nsec is a long, so the comparison casts it to unsigned long (the same width) rather than to u32, matching timespec64_valid(). A u32 cast would truncate on 64-bit; the unsigned long cast also rejects a value that became negative when an out-of-range u32 wire nseconds was assigned to a 32-bit long. Only client-supplied times are checked: SET_TO_SERVER_TIME requests carry no client value. The sattrguard3 ctime is deliberately left alone: an out-of-range guard simply never matches the object's ctime and yields NFS3ERR_NOT_SYNC via the existing guardtime comparison, which is the protocol-correct outcome rather than rejecting the request. | |||||
| CVE-2026-89661 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: NFSD: Prevent post-shutdown use-after-free in unlock_filesystem Writing a filesystem path to /proc/fs/nfsd/unlock_filesystem runs nfsd4_cancel_copy_by_sb() before nfsd_mutex is held and before the handler confirms that nn->nfsd_serv is set. Once nfsd has shut down, nfs4_state_destroy_net() has freed nn->conf_id_hashtbl but left the pointer intact, so the cancel helper iterates freed slab memory as an array of struct list_head and then dereferences a bogus nfs4_client when it takes clp->async_lock. A local administrator holding CAP_SYS_ADMIN can reach this use-after-free by stopping the server and then writing to unlock_filesystem; KASAN reports a slab-use-after-free read in nfsd4_cancel_copy_by_sb(). nfsd4_revoke_states() walks the same state tables and for that reason already runs only under nfsd_mutex with nn->nfsd_serv confirmed present. Move the async COPY cancel into that protected section so every NFSv4 state-table walker on this path observes a running server. Async copies exist only while the server runs, so gating the cancel on nn->nfsd_serv loses nothing. | |||||
| CVE-2026-89645 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: btrfs: drop recovered reloc root refs on recovery failure During relocation recovery, each fs root gets a reference to its relocation root. If loading or adding a later root fails, or if the first transaction commit fails, btrfs_recover_relocation() jumps to out_unset before merge_reloc_roots() and clean_dirty_subvols(). put_reloc_control() drops the list-owned relocation root references, but it does not clear fs_root->reloc_root or drop the references owned by those pointers. Mount cleanup only drops them when BTRFS_FS_ERROR is set, so an error such as -ENOMEM while processing a later root can leave references behind. Keep temporary references to the fs roots associated during recovery. On failure, clear their reloc_root pointers and drop the corresponding references. Once the first transaction commit succeeds, drop only the temporary fs root references and let the normal merge and cleanup paths handle the relocation roots. Fault injection on a pending-relocation image confirmed the cleanup gap. With an injected first-commit failure, 25 fs roots had reloc_root set with fs_error=0. With this fix, the same failure path drops that count to 0 before mount fails. | |||||
| CVE-2026-89629 | 2026-09-11 | N/A | N/A | ||
| In the Linux kernel, the following vulnerability has been resolved: HID: corsair-void: Check size of status and firmware events before reading them Malformed status and firmware events could cause an out-of-bounds read since the size wasn't being checked. Check the size and warn on unexpected values to avoid this. | |||||