Total
19639 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2026-43329 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: flowtable: strictly check for maximum number of actions The maximum number of flowtable hardware offload actions in IPv6 is: * ethernet mangling (4 payload actions, 2 for each ethernet address) * SNAT (4 payload actions) * DNAT (4 payload actions) * Double VLAN (4 vlan actions, 2 for popping vlan, and 2 for pushing) for QinQ. * Redirect (1 action) Which makes 17, while the maximum is 16. But act_ct supports for tunnels actions too. Note that payload action operates at 32-bit word level, so mangling an IPv6 address takes 4 payload actions. Update flow_action_entry_next() calls to check for the maximum number of supported actions. While at it, rise the maximum number of actions per flow from 16 to 24 so this works fine with IPv6 setups. | |||||
| CVE-2026-43321 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Properly mark live registers for indirect jumps For a `gotox rX` instruction the rX register should be marked as used in the compute_insn_live_regs() function. Fix this. | |||||
| CVE-2026-43304 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 9.8 CRITICAL |
| In the Linux kernel, the following vulnerability has been resolved: libceph: define and enforce CEPH_MAX_KEY_LEN When decoding the key, verify that the key material would fit into a fixed-size buffer in process_auth_done() and generally has a sane length. The new CEPH_MAX_KEY_LEN check replaces the existing check for a key with no key material which is a) not universal since CEPH_CRYPTO_NONE has to be excluded and b) doesn't provide much value since a smaller than needed key is just as invalid as no key -- this has to be handled elsewhere anyway. | |||||
| CVE-2026-43303 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: mm/page_alloc: clear page->private in free_pages_prepare() Several subsystems (slub, shmem, ttm, etc.) use page->private but don't clear it before freeing pages. When these pages are later allocated as high-order pages and split via split_page(), tail pages retain stale page->private values. This causes a use-after-free in the swap subsystem. The swap code uses page->private to track swap count continuations, assuming freshly allocated pages have page->private == 0. When stale values are present, swap_count_continued() incorrectly assumes the continuation list is valid and iterates over uninitialized page->lru containing LIST_POISON values, causing a crash: KASAN: maybe wild-memory-access in range [0xdead000000000100-0xdead000000000107] RIP: 0010:__do_sys_swapoff+0x1151/0x1860 Fix this by clearing page->private in free_pages_prepare(), ensuring all freed pages have clean state regardless of previous use. | |||||
| CVE-2026-43280 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: drm/xe: Add bounds check on pat_index to prevent OOB kernel read in madvise When user provides a bogus pat_index value through the madvise IOCTL, the xe_pat_index_get_coh_mode() function performs an array access without validating bounds. This allows a malicious user to trigger an out-of-bounds kernel read from the xe->pat.table array. The vulnerability exists because the validation in madvise_args_are_sane() directly calls xe_pat_index_get_coh_mode(xe, args->pat_index.val) without first checking if pat_index is within [0, xe->pat.n_entries). Although xe_pat_index_get_coh_mode() has a WARN_ON to catch this in debug builds, it still performs the unsafe array access in production kernels. v2(Matthew Auld) - Using array_index_nospec() to mitigate spectre attacks when the value is used v3(Matthew Auld) - Put the declarations at the start of the block (cherry picked from commit 944a3329b05510d55c69c2ef455136e2fc02de29) | |||||
| CVE-2026-43279 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Add sanity check for OOB writes at silencing At silencing the playback URB packets in the implicit fb mode before the actual playback, we blindly assume that the received packets fit with the buffer size. But when the setup in the capture stream differs from the playback stream (e.g. due to the USB core limitation of max packet size), such an inconsistency may lead to OOB writes to the buffer, resulting in a crash. For addressing it, add a sanity check of the transfer buffer size at prepare_silent_urb(), and stop the data copy if the received data overflows. Also, report back the transfer error properly from there, too. Note that this doesn't fix the root cause of the playback error itself, but this merely covers the kernel Oops. | |||||
| CVE-2026-43278 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: dm: clear cloned request bio pointer when last clone bio completes Stale rq->bio values have been observed to cause double-initialization of cloned bios in request-based device-mapper targets, leading to use-after-free and double-free scenarios. One such case occurs when using dm-multipath on top of a PCIe NVMe namespace, where cloned request bios are freed during blk_complete_request(), but rq->bio is left intact. Subsequent clone teardown then attempts to free the same bios again via blk_rq_unprep_clone(). The resulting double-free path looks like: nvme_pci_complete_batch() nvme_complete_batch() blk_mq_end_request_batch() blk_complete_request() // called on a DM clone request bio_endio() // first free of all clone bios ... rq->end_io() // end_clone_request() dm_complete_request(tio->orig) dm_softirq_done() dm_done() dm_end_request() blk_rq_unprep_clone() // second free of clone bios Fix this by clearing the clone request's bio pointer when the last cloned bio completes, ensuring that later teardown paths do not attempt to free already-released bios. | |||||
| CVE-2026-43237 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Refactor amdgpu_gem_va_ioctl for Handling Last Fence Update and Timeline Management v4 This commit simplifies the amdgpu_gem_va_ioctl function, key updates include: - Moved the logic for managing the last update fence directly into amdgpu_gem_va_update_vm. - Introduced checks for the timeline point to enable conditional replacement or addition of fences. v2: Addressed review comments from Christian. v3: Updated comments (Christian). v4: The previous version selected the fence too early and did not manage its reference correctly, which could lead to stale or freed fences being used. This resulted in refcount underflows and could crash when updating GPU timelines. The fence is now chosen only after the VA mapping work is completed, and its reference is taken safely. After exporting it to the VM timeline syncobj, the driver always drops its local fence reference, ensuring balanced refcounting and avoiding use-after-free on dma_fence. Crash signature: [ 205.828135] refcount_t: underflow; use-after-free. [ 205.832963] WARNING: CPU: 30 PID: 7274 at lib/refcount.c:28 refcount_warn_saturate+0xbe/0x110 ... [ 206.074014] Call Trace: [ 206.076488] <TASK> [ 206.078608] amdgpu_gem_va_ioctl+0x6ea/0x740 [amdgpu] [ 206.084040] ? __pfx_amdgpu_gem_va_ioctl+0x10/0x10 [amdgpu] [ 206.089994] drm_ioctl_kernel+0x86/0xe0 [drm] [ 206.094415] drm_ioctl+0x26e/0x520 [drm] [ 206.098424] ? __pfx_amdgpu_gem_va_ioctl+0x10/0x10 [amdgpu] [ 206.104402] amdgpu_drm_ioctl+0x4b/0x80 [amdgpu] [ 206.109387] __x64_sys_ioctl+0x96/0xe0 [ 206.113156] do_syscall_64+0x66/0x2d0 ... [ 206.553351] BUG: unable to handle page fault for address: ffffffffc0dfde90 ... [ 206.553378] RIP: 0010:dma_fence_signal_timestamp_locked+0x39/0xe0 ... [ 206.553405] Call Trace: [ 206.553409] <IRQ> [ 206.553415] ? __pfx_drm_sched_fence_free_rcu+0x10/0x10 [gpu_sched] [ 206.553424] dma_fence_signal+0x30/0x60 [ 206.553427] drm_sched_job_done.isra.0+0x123/0x150 [gpu_sched] [ 206.553434] dma_fence_signal_timestamp_locked+0x6e/0xe0 [ 206.553437] dma_fence_signal+0x30/0x60 [ 206.553441] amdgpu_fence_process+0xd8/0x150 [amdgpu] [ 206.553854] sdma_v4_0_process_trap_irq+0x97/0xb0 [amdgpu] [ 206.554353] edac_mce_amd(E) ee1004(E) [ 206.554270] amdgpu_irq_dispatch+0x150/0x230 [amdgpu] [ 206.554702] amdgpu_ih_process+0x6a/0x180 [amdgpu] [ 206.555101] amdgpu_irq_handler+0x23/0x60 [amdgpu] [ 206.555500] __handle_irq_event_percpu+0x4a/0x1c0 [ 206.555506] handle_irq_event+0x38/0x80 [ 206.555509] handle_edge_irq+0x92/0x1e0 [ 206.555513] __common_interrupt+0x3e/0xb0 [ 206.555519] common_interrupt+0x80/0xa0 [ 206.555525] </IRQ> [ 206.555527] <TASK> ... [ 206.555650] RIP: 0010:dma_fence_signal_timestamp_locked+0x39/0xe0 ... [ 206.555667] Kernel panic - not syncing: Fatal exception in interrupt | |||||
| CVE-2026-43233 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 8.2 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conntrack_h323: fix OOB read in decode_choice() In decode_choice(), the boundary check before get_len() uses the variable `len`, which is still 0 from its initialization at the top of the function: unsigned int type, ext, len = 0; ... if (ext || (son->attr & OPEN)) { BYTE_ALIGN(bs); if (nf_h323_error_boundary(bs, len, 0)) /* len is 0 here */ return H323_ERROR_BOUND; len = get_len(bs); /* OOB read */ When the bitstream is exactly consumed (bs->cur == bs->end), the check nf_h323_error_boundary(bs, 0, 0) evaluates to (bs->cur + 0 > bs->end), which is false. The subsequent get_len() call then dereferences *bs->cur++, reading 1 byte past the end of the buffer. If that byte has bit 7 set, get_len() reads a second byte as well. This can be triggered remotely by sending a crafted Q.931 SETUP message with a User-User Information Element containing exactly 2 bytes of PER-encoded data ({0x08, 0x00}) to port 1720 through a firewall with the nf_conntrack_h323 helper active. The decoder fully consumes the PER buffer before reaching this code path, resulting in a 1-2 byte heap-buffer-overflow read confirmed by AddressSanitizer. Fix this by checking for 2 bytes (the maximum that get_len() may read) instead of the uninitialized `len`. This matches the pattern used at every other get_len() call site in the same file, where the caller checks for 2 bytes of available data before calling get_len(). | |||||
| CVE-2026-43214 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Add SRCU protection for reading PDPTRs in __get_sregs2() Add SRCU read-side protection when reading PDPTR registers in __get_sregs2(). Reading PDPTRs may trigger access to guest memory: kvm_pdptr_read() -> svm_cache_reg() -> load_pdptrs() -> kvm_vcpu_read_guest_page() -> kvm_vcpu_gfn_to_memslot() kvm_vcpu_gfn_to_memslot() dereferences memslots via __kvm_memslots(), which uses srcu_dereference_check() and requires either kvm->srcu or kvm->slots_lock to be held. Currently only vcpu->mutex is held, triggering lockdep warning: ============================= WARNING: suspicious RCU usage in kvm_vcpu_gfn_to_memslot 6.12.59+ #3 Not tainted include/linux/kvm_host.h:1062 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by syz.5.1717/15100: #0: ff1100002f4b00b0 (&vcpu->mutex){+.+.}-{3:3}, at: kvm_vcpu_ioctl+0x1d5/0x1590 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0xf0/0x120 lib/dump_stack.c:120 lockdep_rcu_suspicious+0x1e3/0x270 kernel/locking/lockdep.c:6824 __kvm_memslots include/linux/kvm_host.h:1062 [inline] __kvm_memslots include/linux/kvm_host.h:1059 [inline] kvm_vcpu_memslots include/linux/kvm_host.h:1076 [inline] kvm_vcpu_gfn_to_memslot+0x518/0x5e0 virt/kvm/kvm_main.c:2617 kvm_vcpu_read_guest_page+0x27/0x50 virt/kvm/kvm_main.c:3302 load_pdptrs+0xff/0x4b0 arch/x86/kvm/x86.c:1065 svm_cache_reg+0x1c9/0x230 arch/x86/kvm/svm/svm.c:1688 kvm_pdptr_read arch/x86/kvm/kvm_cache_regs.h:141 [inline] __get_sregs2 arch/x86/kvm/x86.c:11784 [inline] kvm_arch_vcpu_ioctl+0x3e20/0x4aa0 arch/x86/kvm/x86.c:6279 kvm_vcpu_ioctl+0x856/0x1590 virt/kvm/kvm_main.c:4663 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:907 [inline] __se_sys_ioctl fs/ioctl.c:893 [inline] __x64_sys_ioctl+0x18b/0x210 fs/ioctl.c:893 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xbd/0x1d0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Found by Linux Verification Center (linuxtesting.org) with Syzkaller. | |||||
| CVE-2026-43211 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: PCI: Fix pci_slot_trylock() error handling Commit a4e772898f8b ("PCI: Add missing bridge lock to pci_bus_lock()") delegates the bridge device's pci_dev_trylock() to pci_bus_trylock() in pci_slot_trylock(), but it forgets to remove the corresponding pci_dev_unlock() when pci_bus_trylock() fails. Before a4e772898f8b, the code did: if (!pci_dev_trylock(dev)) /* <- lock bridge device */ goto unlock; if (dev->subordinate) { if (!pci_bus_trylock(dev->subordinate)) { pci_dev_unlock(dev); /* <- unlock bridge device */ goto unlock; } } After a4e772898f8b the bridge-device lock is no longer taken, but the pci_dev_unlock(dev) on the failure path was left in place, leading to the bug. This yields one of two errors: 1. A warning that the lock is being unlocked when no one holds it. 2. An incorrect unlock of a lock that belongs to another thread. Fix it by removing the now-redundant pci_dev_unlock(dev) on the failure path. [Same patch later posted by Keith at https://patch.msgid.link/20260116184150.3013258-1-kbusch@meta.com] | |||||
| CVE-2026-43206 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix out-of-bounds write in kfd_event_page_set() The kfd_event_page_set() function writes KFD_SIGNAL_EVENT_LIMIT * 8 bytes via memset without checking the buffer size parameter. This allows unprivileged userspace to trigger an out-of bounds kernel memory write by passing a small buffer, leading to potential privilege escalation. | |||||
| CVE-2026-43198 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 9.8 CRITICAL |
| In the Linux kernel, the following vulnerability has been resolved: tcp: fix potential race in tcp_v6_syn_recv_sock() Code in tcp_v6_syn_recv_sock() after the call to tcp_v4_syn_recv_sock() is done too late. After tcp_v4_syn_recv_sock(), the child socket is already visible from TCP ehash table and other cpus might use it. Since newinet->pinet6 is still pointing to the listener ipv6_pinfo bad things can happen as syzbot found. Move the problematic code in tcp_v6_mapped_child_init() and call this new helper from tcp_v4_syn_recv_sock() before the ehash insertion. This allows the removal of one tcp_sync_mss(), since tcp_v4_syn_recv_sock() will call it with the correct context. | |||||
| CVE-2026-43194 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.5 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: net: consume xmit errors of GSO frames udpgro_frglist.sh and udpgro_bench.sh are the flakiest tests currently in NIPA. They fail in the same exact way, TCP GRO test stalls occasionally and the test gets killed after 10min. These tests use veth to simulate GRO. They attach a trivial ("return XDP_PASS;") XDP program to the veth to force TSO off and NAPI on. Digging into the failure mode we can see that the connection is completely stuck after a burst of drops. The sender's snd_nxt is at sequence number N [1], but the receiver claims to have received (rcv_nxt) up to N + 3 * MSS [2]. Last piece of the puzzle is that senders rtx queue is not empty (let's say the block in the rtx queue is at sequence number N - 4 * MSS [3]). In this state, sender sends a retransmission from the rtx queue with a single segment, and sequence numbers N-4*MSS:N-3*MSS [3]. Receiver sees it and responds with an ACK all the way up to N + 3 * MSS [2]. But sender will reject this ack as TCP_ACK_UNSENT_DATA because it has no recollection of ever sending data that far out [1]. And we are stuck. The root cause is the mess of the xmit return codes. veth returns an error when it can't xmit a frame. We end up with a loss event like this: ------------------------------------------------- | GSO super frame 1 | GSO super frame 2 | |-----------------------------------------------| | seg | seg | seg | seg | seg | seg | seg | seg | | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | ------------------------------------------------- x ok ok <ok>| ok ok ok <x> \\ snd_nxt "x" means packet lost by veth, and "ok" means it went thru. Since veth has TSO disabled in this test it sees individual segments. Segment 1 is on the retransmit queue and will be resent. So why did the sender not advance snd_nxt even tho it clearly did send up to seg 8? tcp_write_xmit() interprets the return code from the core to mean that data has not been sent at all. Since TCP deals with GSO super frames, not individual segment the crux of the problem is that loss of a single segment can be interpreted as loss of all. TCP only sees the last return code for the last segment of the GSO frame (in <> brackets in the diagram above). Of course for the problem to occur we need a setup or a device without a Qdisc. Otherwise Qdisc layer disconnects the protocol layer from the device errors completely. We have multiple ways to fix this. 1) make veth not return an error when it lost a packet. While this is what I think we did in the past, the issue keeps reappearing and it's annoying to debug. The game of whack a mole is not great. 2) fix the damn return codes We only talk about NETDEV_TX_OK and NETDEV_TX_BUSY in the documentation, so maybe we should make the return code from ndo_start_xmit() a boolean. I like that the most, but perhaps some ancient, not-really-networking protocol would suffer. 3) make TCP ignore the errors It is not entirely clear to me what benefit TCP gets from interpreting the result of ip_queue_xmit()? Specifically once the connection is established and we're pushing data - packet loss is just packet loss? 4) this fix Ignore the rc in the Qdisc-less+GSO case, since it's unreliable. We already always return OK in the TCQ_F_CAN_BYPASS case. In the Qdisc-less case let's be a bit more conservative and only mask the GSO errors. This path is taken by non-IP-"networks" like CAN, MCTP etc, so we could regress some ancient thing. This is the simplest, but also maybe the hackiest fix? Similar fix has been proposed by Eric in the past but never committed because original reporter was working with an OOT driver and wasn't providing feedback (see Link). | |||||
| CVE-2026-43190 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 8.2 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: xt_tcpmss: check remaining length before reading optlen Quoting reporter: In net/netfilter/xt_tcpmss.c (lines 53-68), the TCP option parser reads op[i+1] directly without validating the remaining option length. If the last byte of the option field is not EOL/NOP (0/1), the code attempts to index op[i+1]. In the case where i + 1 == optlen, this causes an out-of-bounds read, accessing memory past the optlen boundary (either reading beyond the stack buffer _opt or the following payload). | |||||
| CVE-2026-43187 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: xfs: delete attr leaf freemap entries when empty Back in commit 2a2b5932db6758 ("xfs: fix attr leaf header freemap.size underflow"), Brian Foster observed that it's possible for a small freemap at the end of the end of the xattr entries array to experience a size underflow when subtracting the space consumed by an expansion of the entries array. There are only three freemap entries, which means that it is not a complete index of all free space in the leaf block. This code can leave behind a zero-length freemap entry with a nonzero base. Subsequent setxattr operations can increase the base up to the point that it overlaps with another freemap entry. This isn't in and of itself a problem because the code in _leaf_add that finds free space ignores any freemap entry with zero size. However, there's another bug in the freemap update code in _leaf_add, which is that it fails to update a freemap entry that begins midway through the xattr entry that was just appended to the array. That can result in the freemap containing two entries with the same base but different sizes (0 for the "pushed-up" entry, nonzero for the entry that's actually tracking free space). A subsequent _leaf_add can then allocate xattr namevalue entries on top of the entries array, leading to data loss. But fixing that is for later. For now, eliminate the possibility of confusion by zeroing out the base of any freemap entry that has zero size. Because the freemap is not intended to be a complete index of free space, a subsequent failure to find any free space for a new xattr will trigger block compaction, which regenerates the freemap. It looks like this bug has been in the codebase for quite a long time. | |||||
| CVE-2026-43186 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 9.8 CRITICAL |
| In the Linux kernel, the following vulnerability has been resolved: ipv6: ioam: fix heap buffer overflow in __ioam6_fill_trace_data() On the receive path, __ioam6_fill_trace_data() uses trace->nodelen to decide how much data to write for each node. It trusts this field as-is from the incoming packet, with no consistency check against trace->type (the 24-bit field that tells which data items are present). A crafted packet can set nodelen=0 while setting type bits 0-21, causing the function to write ~100 bytes past the allocated region (into skb_shared_info), which corrupts adjacent heap memory and leads to a kernel panic. Add a shared helper ioam6_trace_compute_nodelen() in ioam6.c to derive the expected nodelen from the type field, and use it: - in ioam6_iptunnel.c (send path, existing validation) to replace the open-coded computation; - in exthdrs.c (receive path, ipv6_hop_ioam) to drop packets whose nodelen is inconsistent with the type field, before any data is written. Per RFC 9197, bits 12-21 are each short (4-octet) fields, so they are included in IOAM6_MASK_SHORT_FIELDS (changed from 0xff100000 to 0xff1ffc00). | |||||
| CVE-2026-43180 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: net: usb: kaweth: remove TX queue manipulation in kaweth_set_rx_mode kaweth_set_rx_mode(), the ndo_set_rx_mode callback, calls netif_stop_queue() and netif_wake_queue(). These are TX queue flow control functions unrelated to RX multicast configuration. The premature netif_wake_queue() can re-enable TX while tx_urb is still in-flight, leading to a double usb_submit_urb() on the same URB: kaweth_start_xmit() { netif_stop_queue(); usb_submit_urb(kaweth->tx_urb); } kaweth_set_rx_mode() { netif_stop_queue(); netif_wake_queue(); // wakes TX queue before URB is done } kaweth_start_xmit() { netif_stop_queue(); usb_submit_urb(kaweth->tx_urb); // URB submitted while active } This triggers the WARN in usb_submit_urb(): "URB submitted while active" This is a similar class of bug fixed in rtl8150 by - commit 958baf5eaee3 ("net: usb: Remove disruptive netif_wake_queue in rtl8150_set_multicast"). Also kaweth_set_rx_mode() is already functionally broken, the real set_rx_mode action is performed by kaweth_async_set_rx_mode(), which in turn is not a no-op only at ndo_open() time. | |||||
| CVE-2026-43176 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: pci: validate release report content before using for RTL8922DE The commit 957eda596c76 ("wifi: rtw89: pci: validate sequence number of TX release report") does validation on existing chips, which somehow a release report of SKB becomes malformed. As no clear cause found, add rules ahead for RTL8922DE to avoid crash if it happens. | |||||
| CVE-2026-43158 | 1 Linux | 1 Linux Kernel | 2026-10-19 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: xfs: fix freemap adjustments when adding xattrs to leaf blocks xfs/592 and xfs/794 both trip this assertion in the leaf block freemap adjustment code after ~20 minutes of running on my test VMs: ASSERT(ichdr->firstused >= ichdr->count * sizeof(xfs_attr_leaf_entry_t) + xfs_attr3_leaf_hdr_size(leaf)); Upon enabling quite a lot more debugging code, I narrowed this down to fsstress trying to set a local extended attribute with namelen=3 and valuelen=71. This results in an entry size of 80 bytes. At the start of xfs_attr3_leaf_add_work, the freemap looks like this: i 0 base 448 size 0 rhs 448 count 46 i 1 base 388 size 132 rhs 448 count 46 i 2 base 2120 size 4 rhs 448 count 46 firstused = 520 where "rhs" is the first byte past the end of the leaf entry array. This is inconsistent -- the entries array ends at byte 448, but freemap[1] says there's free space starting at byte 388! By the end of the function, the freemap is in worse shape: i 0 base 456 size 0 rhs 456 count 47 i 1 base 388 size 52 rhs 456 count 47 i 2 base 2120 size 4 rhs 456 count 47 firstused = 440 Important note: 388 is not aligned with the entries array element size of 8 bytes. Based on the incorrect freemap, the name area starts at byte 440, which is below the end of the entries array! That's why the assertion triggers and the filesystem shuts down. How did we end up here? First, recall from the previous patch that the freemap array in an xattr leaf block is not intended to be a comprehensive map of all free space in the leaf block. In other words, it's perfectly legal to have a leaf block with: * 376 bytes in use by the entries array * freemap[0] has [base = 376, size = 8] * freemap[1] has [base = 388, size = 1500] * the space between 376 and 388 is free, but the freemap stopped tracking that some time ago If we add one xattr, the entries array grows to 384 bytes, and freemap[0] becomes [base = 384, size = 0]. So far, so good. But if we add a second xattr, the entries array grows to 392 bytes, and freemap[0] gets pushed up to [base = 392, size = 0]. This is bad, because freemap[1] hasn't been updated, and now the entries array and the free space claim the same space. The fix here is to adjust all freemap entries so that none of them collide with the entries array. Note that this fix relies on commit 2a2b5932db6758 ("xfs: fix attr leaf header freemap.size underflow") and the previous patch that resets zero length freemap entries to have base = 0. | |||||