Total
771 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2024-57889 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking If a device uses MCP23xxx IO expander to receive IRQs, the following bug can happen: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:283 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, ... preempt_count: 1, expected: 0 ... Call Trace: ... __might_resched+0x104/0x10e __might_sleep+0x3e/0x62 mutex_lock+0x20/0x4c regmap_lock_mutex+0x10/0x18 regmap_update_bits_base+0x2c/0x66 mcp23s08_irq_set_type+0x1ae/0x1d6 __irq_set_trigger+0x56/0x172 __setup_irq+0x1e6/0x646 request_threaded_irq+0xb6/0x160 ... We observed the problem while experimenting with a touchscreen driver which used MCP23017 IO expander (I2C). The regmap in the pinctrl-mcp23s08 driver uses a mutex for protection from concurrent accesses, which is the default for regmaps without .fast_io, .disable_locking, etc. mcp23s08_irq_set_type() calls regmap_update_bits_base(), and the latter locks the mutex. However, __setup_irq() locks desc->lock spinlock before calling these functions. As a result, the system tries to lock the mutex whole holding the spinlock. It seems, the internal regmap locks are not needed in this driver at all. mcp->lock seems to protect the regmap from concurrent accesses already, except, probably, in mcp_pinconf_get/set. mcp23s08_irq_set_type() and mcp23s08_irq_mask/unmask() are called under chip_bus_lock(), which calls mcp23s08_irq_bus_lock(). The latter takes mcp->lock and enables regmap caching, so that the potentially slow I2C accesses are deferred until chip_bus_unlock(). The accesses to the regmap from mcp23s08_probe_one() do not need additional locking. In all remaining places where the regmap is accessed, except mcp_pinconf_get/set(), the driver already takes mcp->lock. This patch adds locking in mcp_pinconf_get/set() and disables internal locking in the regmap config. Among other things, it fixes the sleeping in atomic context described above. | |||||
| CVE-2024-57807 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: scsi: megaraid_sas: Fix for a potential deadlock This fixes a 'possible circular locking dependency detected' warning CPU0 CPU1 ---- ---- lock(&instance->reset_mutex); lock(&shost->scan_mutex); lock(&instance->reset_mutex); lock(&shost->scan_mutex); Fix this by temporarily releasing the reset_mutex. | |||||
| CVE-2024-56744 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid potential deadlock in f2fs_record_stop_reason() syzbot reports deadlock issue of f2fs as below: ====================================================== WARNING: possible circular locking dependency detected 6.12.0-rc3-syzkaller-00087-gc964ced77262 #0 Not tainted ------------------------------------------------------ kswapd0/79 is trying to acquire lock: ffff888011824088 (&sbi->sb_lock){++++}-{3:3}, at: f2fs_down_write fs/f2fs/f2fs.h:2199 [inline] ffff888011824088 (&sbi->sb_lock){++++}-{3:3}, at: f2fs_record_stop_reason+0x52/0x1d0 fs/f2fs/super.c:4068 but task is already holding lock: ffff88804bd92610 (sb_internal#2){.+.+}-{0:0}, at: f2fs_evict_inode+0x662/0x15c0 fs/f2fs/inode.c:842 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (sb_internal#2){.+.+}-{0:0}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5825 percpu_down_read include/linux/percpu-rwsem.h:51 [inline] __sb_start_write include/linux/fs.h:1716 [inline] sb_start_intwrite+0x4d/0x1c0 include/linux/fs.h:1899 f2fs_evict_inode+0x662/0x15c0 fs/f2fs/inode.c:842 evict+0x4e8/0x9b0 fs/inode.c:725 f2fs_evict_inode+0x1a4/0x15c0 fs/f2fs/inode.c:807 evict+0x4e8/0x9b0 fs/inode.c:725 dispose_list fs/inode.c:774 [inline] prune_icache_sb+0x239/0x2f0 fs/inode.c:963 super_cache_scan+0x38c/0x4b0 fs/super.c:223 do_shrink_slab+0x701/0x1160 mm/shrinker.c:435 shrink_slab+0x1093/0x14d0 mm/shrinker.c:662 shrink_one+0x43b/0x850 mm/vmscan.c:4818 shrink_many mm/vmscan.c:4879 [inline] lru_gen_shrink_node mm/vmscan.c:4957 [inline] shrink_node+0x3799/0x3de0 mm/vmscan.c:5937 kswapd_shrink_node mm/vmscan.c:6765 [inline] balance_pgdat mm/vmscan.c:6957 [inline] kswapd+0x1ca3/0x3700 mm/vmscan.c:7226 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 -> #1 (fs_reclaim){+.+.}-{0:0}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5825 __fs_reclaim_acquire mm/page_alloc.c:3834 [inline] fs_reclaim_acquire+0x88/0x130 mm/page_alloc.c:3848 might_alloc include/linux/sched/mm.h:318 [inline] prepare_alloc_pages+0x147/0x5b0 mm/page_alloc.c:4493 __alloc_pages_noprof+0x16f/0x710 mm/page_alloc.c:4722 alloc_pages_mpol_noprof+0x3e8/0x680 mm/mempolicy.c:2265 alloc_pages_noprof mm/mempolicy.c:2345 [inline] folio_alloc_noprof+0x128/0x180 mm/mempolicy.c:2352 filemap_alloc_folio_noprof+0xdf/0x500 mm/filemap.c:1010 do_read_cache_folio+0x2eb/0x850 mm/filemap.c:3787 read_mapping_folio include/linux/pagemap.h:1011 [inline] f2fs_commit_super+0x3c0/0x7d0 fs/f2fs/super.c:4032 f2fs_record_stop_reason+0x13b/0x1d0 fs/f2fs/super.c:4079 f2fs_handle_critical_error+0x2ac/0x5c0 fs/f2fs/super.c:4174 f2fs_write_inode+0x35f/0x4d0 fs/f2fs/inode.c:785 write_inode fs/fs-writeback.c:1503 [inline] __writeback_single_inode+0x711/0x10d0 fs/fs-writeback.c:1723 writeback_single_inode+0x1f3/0x660 fs/fs-writeback.c:1779 sync_inode_metadata+0xc4/0x120 fs/fs-writeback.c:2849 f2fs_release_file+0xa8/0x100 fs/f2fs/file.c:1941 __fput+0x23f/0x880 fs/file_table.c:431 task_work_run+0x24f/0x310 kernel/task_work.c:228 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop kernel/entry/common.c:114 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:328 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x168/0x370 kernel/entry/common.c:218 do_syscall_64+0x100/0x230 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f ---truncated--- | |||||
| CVE-2024-56743 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: nfs_common: must not hold RCU while calling nfsd_file_put_local Move holding the RCU from nfs_to_nfsd_file_put_local to nfs_to_nfsd_net_put. It is the call to nfs_to->nfsd_serv_put that requires the RCU anyway (the puts for nfsd_file and netns were combined to avoid an extra indirect reference but that micro-optimization isn't possible now). This fixes xfstests generic/013 and it triggering: "Voluntary context switch within RCU read-side critical section!" [ 143.545738] Call Trace: [ 143.546206] <TASK> [ 143.546625] ? show_regs+0x6d/0x80 [ 143.547267] ? __warn+0x91/0x140 [ 143.547951] ? rcu_note_context_switch+0x496/0x5d0 [ 143.548856] ? report_bug+0x193/0x1a0 [ 143.549557] ? handle_bug+0x63/0xa0 [ 143.550214] ? exc_invalid_op+0x1d/0x80 [ 143.550938] ? asm_exc_invalid_op+0x1f/0x30 [ 143.551736] ? rcu_note_context_switch+0x496/0x5d0 [ 143.552634] ? wakeup_preempt+0x62/0x70 [ 143.553358] __schedule+0xaa/0x1380 [ 143.554025] ? _raw_spin_unlock_irqrestore+0x12/0x40 [ 143.554958] ? try_to_wake_up+0x1fe/0x6b0 [ 143.555715] ? wake_up_process+0x19/0x20 [ 143.556452] schedule+0x2e/0x120 [ 143.557066] schedule_preempt_disabled+0x19/0x30 [ 143.557933] rwsem_down_read_slowpath+0x24d/0x4a0 [ 143.558818] ? xfs_efi_item_format+0x50/0xc0 [xfs] [ 143.559894] down_read+0x4e/0xb0 [ 143.560519] xlog_cil_commit+0x1b2/0xbc0 [xfs] [ 143.561460] ? _raw_spin_unlock+0x12/0x30 [ 143.562212] ? xfs_inode_item_precommit+0xc7/0x220 [xfs] [ 143.563309] ? xfs_trans_run_precommits+0x69/0xd0 [xfs] [ 143.564394] __xfs_trans_commit+0xb5/0x330 [xfs] [ 143.565367] xfs_trans_roll+0x48/0xc0 [xfs] [ 143.566262] xfs_defer_trans_roll+0x57/0x100 [xfs] [ 143.567278] xfs_defer_finish_noroll+0x27a/0x490 [xfs] [ 143.568342] xfs_defer_finish+0x1a/0x80 [xfs] [ 143.569267] xfs_bunmapi_range+0x4d/0xb0 [xfs] [ 143.570208] xfs_itruncate_extents_flags+0x13d/0x230 [xfs] [ 143.571353] xfs_free_eofblocks+0x12e/0x190 [xfs] [ 143.572359] xfs_file_release+0x12d/0x140 [xfs] [ 143.573324] __fput+0xe8/0x2d0 [ 143.573922] __fput_sync+0x1d/0x30 [ 143.574574] nfsd_filp_close+0x33/0x60 [nfsd] [ 143.575430] nfsd_file_free+0x96/0x150 [nfsd] [ 143.576274] nfsd_file_put+0xf7/0x1a0 [nfsd] [ 143.577104] nfsd_file_put_local+0x18/0x30 [nfsd] [ 143.578070] nfs_close_local_fh+0x101/0x110 [nfs_localio] [ 143.579079] __put_nfs_open_context+0xc9/0x180 [nfs] [ 143.580031] nfs_file_clear_open_context+0x4a/0x60 [nfs] [ 143.581038] nfs_file_release+0x3e/0x60 [nfs] [ 143.581879] __fput+0xe8/0x2d0 [ 143.582464] __fput_sync+0x1d/0x30 [ 143.583108] __x64_sys_close+0x41/0x80 [ 143.583823] x64_sys_call+0x189a/0x20d0 [ 143.584552] do_syscall_64+0x64/0x170 [ 143.585240] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 143.586185] RIP: 0033:0x7f3c5153efd7 | |||||
| CVE-2024-56687 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: usb: musb: Fix hardware lockup on first Rx endpoint request There is a possibility that a request's callback could be invoked from usb_ep_queue() (call trace below, supplemented with missing calls): req->complete from usb_gadget_giveback_request (drivers/usb/gadget/udc/core.c:999) usb_gadget_giveback_request from musb_g_giveback (drivers/usb/musb/musb_gadget.c:147) musb_g_giveback from rxstate (drivers/usb/musb/musb_gadget.c:784) rxstate from musb_ep_restart (drivers/usb/musb/musb_gadget.c:1169) musb_ep_restart from musb_ep_restart_resume_work (drivers/usb/musb/musb_gadget.c:1176) musb_ep_restart_resume_work from musb_queue_resume_work (drivers/usb/musb/musb_core.c:2279) musb_queue_resume_work from musb_gadget_queue (drivers/usb/musb/musb_gadget.c:1241) musb_gadget_queue from usb_ep_queue (drivers/usb/gadget/udc/core.c:300) According to the docstring of usb_ep_queue(), this should not happen: "Note that @req's ->complete() callback must never be called from within usb_ep_queue() as that can create deadlock situations." In fact, a hardware lockup might occur in the following sequence: 1. The gadget is initialized using musb_gadget_enable(). 2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an interrupt. 3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an empty queue (next_request() returns NULL). The interrupt flag has already been cleared by the glue layer handler, but the RXPKTRDY flag remains set. 4. The first request is enqueued using usb_ep_queue(), leading to the call of req->complete(), as shown in the call trace above. 5. If the callback enables IRQs and another packet is waiting, step (3) repeats. The request queue is empty because usb_g_giveback() removes the request before invoking the callback. 6. The endpoint remains locked up, as the interrupt triggered by hardware setting the RXPKTRDY flag has been handled, but the flag itself remains set. For this scenario to occur, it is only necessary for IRQs to be enabled at some point during the complete callback. This happens with the USB Ethernet gadget, whose rx_complete() callback calls netif_rx(). If called in the task context, netif_rx() disables the bottom halves (BHs). When the BHs are re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The gadget itself is initialized at module load (or at boot if built-in), but the first request is enqueued when the network interface is brought up, triggering rx_complete() in the task context via ioctl(). If a packet arrives while the interface is down, it can prevent the interface from receiving any further packets from the USB host. The situation is quite complicated with many parties involved. This particular issue can be resolved in several possible ways: 1. Ensure that callbacks never enable IRQs. This would be difficult to enforce, as discovering how netif_rx() interacts with interrupts was already quite challenging and u_ether is not the only function driver. Similar "bugs" could be hidden in other drivers as well. 2. Disable MUSB interrupts in musb_g_giveback() before calling the callback and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(), for example). This would ensure that MUSB interrupts are not handled during the callback, even if IRQs are enabled. In fact, it would allow IRQs to be enabled when releasing the lock. However, this feels like an inelegant hack. 3. Modify the interrupt handler to clear the RXPKTRDY flag if the request queue is empty. While this approach also feels like a hack, it wastes CPU time by attempting to handle incoming packets when the software is not ready to process them. 4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart(). This ensures that the hardware can receive packets when there is at least one request in the queue. Once I ---truncated--- | |||||
| CVE-2024-56585 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: LoongArch: Fix sleeping in atomic context for PREEMPT_RT Commit bab1c299f3945ffe79 ("LoongArch: Fix sleeping in atomic context in setup_tlb_handler()") changes the gfp flag from GFP_KERNEL to GFP_ATOMIC for alloc_pages_node(). However, for PREEMPT_RT kernels we can still get a "sleeping in atomic context" error: [ 0.372259] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 [ 0.372266] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1 [ 0.372268] preempt_count: 1, expected: 0 [ 0.372270] RCU nest depth: 1, expected: 1 [ 0.372272] 3 locks held by swapper/1/0: [ 0.372274] #0: 900000000c9f5e60 (&pcp->lock){+.+.}-{3:3}, at: get_page_from_freelist+0x524/0x1c60 [ 0.372294] #1: 90000000087013b8 (rcu_read_lock){....}-{1:3}, at: rt_spin_trylock+0x50/0x140 [ 0.372305] #2: 900000047fffd388 (&zone->lock){+.+.}-{3:3}, at: __rmqueue_pcplist+0x30c/0xea0 [ 0.372314] irq event stamp: 0 [ 0.372316] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [ 0.372322] hardirqs last disabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0 [ 0.372329] softirqs last enabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0 [ 0.372335] softirqs last disabled at (0): [<0000000000000000>] 0x0 [ 0.372341] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 6.12.0-rc7+ #1891 [ 0.372346] Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.0-prebeta9 10/21/2022 [ 0.372349] Stack : 0000000000000089 9000000005a0db9c 90000000071519c8 9000000100388000 [ 0.372486] 900000010038b890 0000000000000000 900000010038b898 9000000007e53788 [ 0.372492] 900000000815bcc8 900000000815bcc0 900000010038b700 0000000000000001 [ 0.372498] 0000000000000001 4b031894b9d6b725 00000000055ec000 9000000100338fc0 [ 0.372503] 00000000000000c4 0000000000000001 000000000000002d 0000000000000003 [ 0.372509] 0000000000000030 0000000000000003 00000000055ec000 0000000000000003 [ 0.372515] 900000000806d000 9000000007e53788 00000000000000b0 0000000000000004 [ 0.372521] 0000000000000000 0000000000000000 900000000c9f5f10 0000000000000000 [ 0.372526] 90000000076f12d8 9000000007e53788 9000000005924778 0000000000000000 [ 0.372532] 00000000000000b0 0000000000000004 0000000000000000 0000000000070000 [ 0.372537] ... [ 0.372540] Call Trace: [ 0.372542] [<9000000005924778>] show_stack+0x38/0x180 [ 0.372548] [<90000000071519c4>] dump_stack_lvl+0x94/0xe4 [ 0.372555] [<900000000599b880>] __might_resched+0x1a0/0x260 [ 0.372561] [<90000000071675cc>] rt_spin_lock+0x4c/0x140 [ 0.372565] [<9000000005cbb768>] __rmqueue_pcplist+0x308/0xea0 [ 0.372570] [<9000000005cbed84>] get_page_from_freelist+0x564/0x1c60 [ 0.372575] [<9000000005cc0d98>] __alloc_pages_noprof+0x218/0x1820 [ 0.372580] [<900000000593b36c>] tlb_init+0x1ac/0x298 [ 0.372585] [<9000000005924b74>] per_cpu_trap_init+0x114/0x140 [ 0.372589] [<9000000005921964>] cpu_probe+0x4e4/0xa60 [ 0.372592] [<9000000005934874>] start_secondary+0x34/0xc0 [ 0.372599] [<900000000715615c>] smpboot_entry+0x64/0x6c This is because in PREEMPT_RT kernels normal spinlocks are replaced by rt spinlocks and rt_spin_lock() will cause sleeping. Fix it by disabling NUMA optimization completely for PREEMPT_RT kernels. | |||||
| CVE-2024-56559 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: combine all TLB flush operations of KASAN shadow virtual address into one operation When compiling kernel source 'make -j $(nproc)' with the up-and-running KASAN-enabled kernel on a 256-core machine, the following soft lockup is shown: watchdog: BUG: soft lockup - CPU#28 stuck for 22s! [kworker/28:1:1760] CPU: 28 PID: 1760 Comm: kworker/28:1 Kdump: loaded Not tainted 6.10.0-rc5 #95 Workqueue: events drain_vmap_area_work RIP: 0010:smp_call_function_many_cond+0x1d8/0xbb0 Code: 38 c8 7c 08 84 c9 0f 85 49 08 00 00 8b 45 08 a8 01 74 2e 48 89 f1 49 89 f7 48 c1 e9 03 41 83 e7 07 4c 01 e9 41 83 c7 03 f3 90 <0f> b6 01 41 38 c7 7c 08 84 c0 0f 85 d4 06 00 00 8b 45 08 a8 01 75 RSP: 0018:ffffc9000cb3fb60 EFLAGS: 00000202 RAX: 0000000000000011 RBX: ffff8883bc4469c0 RCX: ffffed10776e9949 RDX: 0000000000000002 RSI: ffff8883bb74ca48 RDI: ffffffff8434dc50 RBP: ffff8883bb74ca40 R08: ffff888103585dc0 R09: ffff8884533a1800 R10: 0000000000000004 R11: ffffffffffffffff R12: ffffed1077888d39 R13: dffffc0000000000 R14: ffffed1077888d38 R15: 0000000000000003 FS: 0000000000000000(0000) GS:ffff8883bc400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005577b5c8d158 CR3: 0000000004850000 CR4: 0000000000350ef0 Call Trace: <IRQ> ? watchdog_timer_fn+0x2cd/0x390 ? __pfx_watchdog_timer_fn+0x10/0x10 ? __hrtimer_run_queues+0x300/0x6d0 ? sched_clock_cpu+0x69/0x4e0 ? __pfx___hrtimer_run_queues+0x10/0x10 ? srso_return_thunk+0x5/0x5f ? ktime_get_update_offsets_now+0x7f/0x2a0 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? hrtimer_interrupt+0x2ca/0x760 ? __sysvec_apic_timer_interrupt+0x8c/0x2b0 ? sysvec_apic_timer_interrupt+0x6a/0x90 </IRQ> <TASK> ? asm_sysvec_apic_timer_interrupt+0x16/0x20 ? smp_call_function_many_cond+0x1d8/0xbb0 ? __pfx_do_kernel_range_flush+0x10/0x10 on_each_cpu_cond_mask+0x20/0x40 flush_tlb_kernel_range+0x19b/0x250 ? srso_return_thunk+0x5/0x5f ? kasan_release_vmalloc+0xa7/0xc0 purge_vmap_node+0x357/0x820 ? __pfx_purge_vmap_node+0x10/0x10 __purge_vmap_area_lazy+0x5b8/0xa10 drain_vmap_area_work+0x21/0x30 process_one_work+0x661/0x10b0 worker_thread+0x844/0x10e0 ? srso_return_thunk+0x5/0x5f ? __kthread_parkme+0x82/0x140 ? __pfx_worker_thread+0x10/0x10 kthread+0x2a5/0x370 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x30/0x70 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Debugging Analysis: 1. The following ftrace log shows that the lockup CPU spends too much time iterating vmap_nodes and flushing TLB when purging vm_area structures. (Some info is trimmed). kworker: funcgraph_entry: | drain_vmap_area_work() { kworker: funcgraph_entry: | mutex_lock() { kworker: funcgraph_entry: 1.092 us | __cond_resched(); kworker: funcgraph_exit: 3.306 us | } ... ... kworker: funcgraph_entry: | flush_tlb_kernel_range() { ... ... kworker: funcgraph_exit: # 7533.649 us | } ... ... kworker: funcgraph_entry: 2.344 us | mutex_unlock(); kworker: funcgraph_exit: $ 23871554 us | } The drain_vmap_area_work() spends over 23 seconds. There are 2805 flush_tlb_kernel_range() calls in the ftrace log. * One is called in __purge_vmap_area_lazy(). * Others are called by purge_vmap_node->kasan_release_vmalloc. purge_vmap_node() iteratively releases kasan vmalloc allocations and flushes TLB for each vmap_area. - [Rough calculation] Each flush_tlb_kernel_range() runs about 7.5ms. -- 2804 * 7.5ms = 21.03 seconds. -- That's why a soft lock is triggered. 2. Extending the soft lockup time can work around the issue (For example, # echo ---truncated--- | |||||
| CVE-2024-56533 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: usx2y: Use snd_card_free_when_closed() at disconnection The USB disconnect callback is supposed to be short and not too-long waiting. OTOH, the current code uses snd_card_free() at disconnection, but this waits for the close of all used fds, hence it can take long. It eventually blocks the upper layer USB ioctls, which may trigger a soft lockup. An easy workaround is to replace snd_card_free() with snd_card_free_when_closed(). This variant returns immediately while the release of resources is done asynchronously by the card device release at the last close. | |||||
| CVE-2024-56532 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: us122l: Use snd_card_free_when_closed() at disconnection The USB disconnect callback is supposed to be short and not too-long waiting. OTOH, the current code uses snd_card_free() at disconnection, but this waits for the close of all used fds, hence it can take long. It eventually blocks the upper layer USB ioctls, which may trigger a soft lockup. An easy workaround is to replace snd_card_free() with snd_card_free_when_closed(). This variant returns immediately while the release of resources is done asynchronously by the card device release at the last close. The loop of us122l->mmap_count check is dropped as well. The check is useless for the asynchronous operation with *_when_closed(). | |||||
| CVE-2024-55642 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: block: Prevent potential deadlocks in zone write plug error recovery Zone write plugging for handling writes to zones of a zoned block device always execute a zone report whenever a write BIO to a zone fails. The intent of this is to ensure that the tracking of a zone write pointer is always correct to ensure that the alignment to a zone write pointer of write BIOs can be checked on submission and that we can always correctly emulate zone append operations using regular write BIOs. However, this error recovery scheme introduces a potential deadlock if a device queue freeze is initiated while BIOs are still plugged in a zone write plug and one of these write operation fails. In such case, the disk zone write plug error recovery work is scheduled and executes a report zone. This in turn can result in a request allocation in the underlying driver to issue the report zones command to the device. But with the device queue freeze already started, this allocation will block, preventing the report zone execution and the continuation of the processing of the plugged BIOs. As plugged BIOs hold a queue usage reference, the queue freeze itself will never complete, resulting in a deadlock. Avoid this problem by completely removing from the zone write plugging code the use of report zones operations after a failed write operation, instead relying on the device user to either execute a report zones, reset the zone, finish the zone, or give up writing to the device (which is a fairly common pattern for file systems which degrade to read-only after write failures). This is not an unreasonnable requirement as all well-behaved applications, FSes and device mapper already use report zones to recover from write errors whenever possible by comparing the current position of a zone write pointer with what their assumption about the position is. The changes to remove the automatic error recovery are as follows: - Completely remove the error recovery work and its associated resources (zone write plug list head, disk error list, and disk zone_wplugs_work work struct). This also removes the functions disk_zone_wplug_set_error() and disk_zone_wplug_clear_error(). - Change the BLK_ZONE_WPLUG_ERROR zone write plug flag into BLK_ZONE_WPLUG_NEED_WP_UPDATE. This new flag is set for a zone write plug whenever a write opration targetting the zone of the zone write plug fails. This flag indicates that the zone write pointer offset is not reliable and that it must be updated when the next report zone, reset zone, finish zone or disk revalidation is executed. - Modify blk_zone_write_plug_bio_endio() to set the BLK_ZONE_WPLUG_NEED_WP_UPDATE flag for the target zone of a failed write BIO. - Modify the function disk_zone_wplug_set_wp_offset() to clear this new flag, thus implementing recovery of a correct write pointer offset with the reset (all) zone and finish zone operations. - Modify blkdev_report_zones() to always use the disk_report_zones_cb() callback so that disk_zone_wplug_sync_wp_offset() can be called for any zone marked with the BLK_ZONE_WPLUG_NEED_WP_UPDATE flag. This implements recovery of a correct write pointer offset for zone write plugs marked with BLK_ZONE_WPLUG_NEED_WP_UPDATE and within the range of the report zones operation executed by the user. - Modify blk_revalidate_seq_zone() to call disk_zone_wplug_sync_wp_offset() for all sequential write required zones when a zoned block device is revalidated, thus always resolving any inconsistency between the write pointer offset of zone write plugs and the actual write pointer position of sequential zones. | |||||
| CVE-2024-54460 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: iso: Fix circular lock in iso_listen_bis This fixes the circular locking dependency warning below, by releasing the socket lock before enterning iso_listen_bis, to avoid any potential deadlock with hdev lock. [ 75.307983] ====================================================== [ 75.307984] WARNING: possible circular locking dependency detected [ 75.307985] 6.12.0-rc6+ #22 Not tainted [ 75.307987] ------------------------------------------------------ [ 75.307987] kworker/u81:2/2623 is trying to acquire lock: [ 75.307988] ffff8fde1769da58 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO) at: iso_connect_cfm+0x253/0x840 [bluetooth] [ 75.308021] but task is already holding lock: [ 75.308022] ffff8fdd61a10078 (&hdev->lock) at: hci_le_per_adv_report_evt+0x47/0x2f0 [bluetooth] [ 75.308053] which lock already depends on the new lock. [ 75.308054] the existing dependency chain (in reverse order) is: [ 75.308055] -> #1 (&hdev->lock){+.+.}-{3:3}: [ 75.308057] __mutex_lock+0xad/0xc50 [ 75.308061] mutex_lock_nested+0x1b/0x30 [ 75.308063] iso_sock_listen+0x143/0x5c0 [bluetooth] [ 75.308085] __sys_listen_socket+0x49/0x60 [ 75.308088] __x64_sys_listen+0x4c/0x90 [ 75.308090] x64_sys_call+0x2517/0x25f0 [ 75.308092] do_syscall_64+0x87/0x150 [ 75.308095] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 75.308098] -> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: [ 75.308100] __lock_acquire+0x155e/0x25f0 [ 75.308103] lock_acquire+0xc9/0x300 [ 75.308105] lock_sock_nested+0x32/0x90 [ 75.308107] iso_connect_cfm+0x253/0x840 [bluetooth] [ 75.308128] hci_connect_cfm+0x6c/0x190 [bluetooth] [ 75.308155] hci_le_per_adv_report_evt+0x27b/0x2f0 [bluetooth] [ 75.308180] hci_le_meta_evt+0xe7/0x200 [bluetooth] [ 75.308206] hci_event_packet+0x21f/0x5c0 [bluetooth] [ 75.308230] hci_rx_work+0x3ae/0xb10 [bluetooth] [ 75.308254] process_one_work+0x212/0x740 [ 75.308256] worker_thread+0x1bd/0x3a0 [ 75.308258] kthread+0xe4/0x120 [ 75.308259] ret_from_fork+0x44/0x70 [ 75.308261] ret_from_fork_asm+0x1a/0x30 [ 75.308263] other info that might help us debug this: [ 75.308264] Possible unsafe locking scenario: [ 75.308264] CPU0 CPU1 [ 75.308265] ---- ---- [ 75.308265] lock(&hdev->lock); [ 75.308267] lock(sk_lock- AF_BLUETOOTH-BTPROTO_ISO); [ 75.308268] lock(&hdev->lock); [ 75.308269] lock(sk_lock-AF_BLUETOOTH-BTPROTO_ISO); [ 75.308270] *** DEADLOCK *** [ 75.308271] 4 locks held by kworker/u81:2/2623: [ 75.308272] #0: ffff8fdd66e52148 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_one_work+0x443/0x740 [ 75.308276] #1: ffffafb488b7fe48 ((work_completion)(&hdev->rx_work)), at: process_one_work+0x1ce/0x740 [ 75.308280] #2: ffff8fdd61a10078 (&hdev->lock){+.+.}-{3:3} at: hci_le_per_adv_report_evt+0x47/0x2f0 [bluetooth] [ 75.308304] #3: ffffffffb6ba4900 (rcu_read_lock){....}-{1:2}, at: hci_connect_cfm+0x29/0x190 [bluetooth] | |||||
| CVE-2024-54191 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: iso: Fix circular lock in iso_conn_big_sync This fixes the circular locking dependency warning below, by reworking iso_sock_recvmsg, to ensure that the socket lock is always released before calling a function that locks hdev. [ 561.670344] ====================================================== [ 561.670346] WARNING: possible circular locking dependency detected [ 561.670349] 6.12.0-rc6+ #26 Not tainted [ 561.670351] ------------------------------------------------------ [ 561.670353] iso-tester/3289 is trying to acquire lock: [ 561.670355] ffff88811f600078 (&hdev->lock){+.+.}-{3:3}, at: iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670405] but task is already holding lock: [ 561.670407] ffff88815af58258 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}, at: iso_sock_recvmsg+0xbf/0x500 [bluetooth] [ 561.670450] which lock already depends on the new lock. [ 561.670452] the existing dependency chain (in reverse order) is: [ 561.670453] -> #2 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}: [ 561.670458] lock_acquire+0x7c/0xc0 [ 561.670463] lock_sock_nested+0x3b/0xf0 [ 561.670467] bt_accept_dequeue+0x1a5/0x4d0 [bluetooth] [ 561.670510] iso_sock_accept+0x271/0x830 [bluetooth] [ 561.670547] do_accept+0x3dd/0x610 [ 561.670550] __sys_accept4+0xd8/0x170 [ 561.670553] __x64_sys_accept+0x74/0xc0 [ 561.670556] x64_sys_call+0x17d6/0x25f0 [ 561.670559] do_syscall_64+0x87/0x150 [ 561.670563] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670567] -> #1 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: [ 561.670571] lock_acquire+0x7c/0xc0 [ 561.670574] lock_sock_nested+0x3b/0xf0 [ 561.670577] iso_sock_listen+0x2de/0xf30 [bluetooth] [ 561.670617] __sys_listen_socket+0xef/0x130 [ 561.670620] __x64_sys_listen+0xe1/0x190 [ 561.670623] x64_sys_call+0x2517/0x25f0 [ 561.670626] do_syscall_64+0x87/0x150 [ 561.670629] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670632] -> #0 (&hdev->lock){+.+.}-{3:3}: [ 561.670636] __lock_acquire+0x32ad/0x6ab0 [ 561.670639] lock_acquire.part.0+0x118/0x360 [ 561.670642] lock_acquire+0x7c/0xc0 [ 561.670644] __mutex_lock+0x18d/0x12f0 [ 561.670647] mutex_lock_nested+0x1b/0x30 [ 561.670651] iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670687] iso_sock_recvmsg+0x3e9/0x500 [bluetooth] [ 561.670722] sock_recvmsg+0x1d5/0x240 [ 561.670725] sock_read_iter+0x27d/0x470 [ 561.670727] vfs_read+0x9a0/0xd30 [ 561.670731] ksys_read+0x1a8/0x250 [ 561.670733] __x64_sys_read+0x72/0xc0 [ 561.670736] x64_sys_call+0x1b12/0x25f0 [ 561.670738] do_syscall_64+0x87/0x150 [ 561.670741] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670744] other info that might help us debug this: [ 561.670745] Chain exists of: &hdev->lock --> sk_lock-AF_BLUETOOTH-BTPROTO_ISO --> sk_lock-AF_BLUETOOTH [ 561.670751] Possible unsafe locking scenario: [ 561.670753] CPU0 CPU1 [ 561.670754] ---- ---- [ 561.670756] lock(sk_lock-AF_BLUETOOTH); [ 561.670758] lock(sk_lock AF_BLUETOOTH-BTPROTO_ISO); [ 561.670761] lock(sk_lock-AF_BLUETOOTH); [ 561.670764] lock(&hdev->lock); [ 561.670767] *** DEADLOCK *** | |||||
| CVE-2024-53086 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/xe: Drop VM dma-resv lock on xe_sync_in_fence_get failure in exec IOCTL Upon failure all locks need to be dropped before returning to the user. (cherry picked from commit 7d1a4258e602ffdce529f56686925034c1b3b095) | |||||
| CVE-2024-53085 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: tpm: Lock TPM chip in tpm_pm_suspend() first Setting TPM_CHIP_FLAG_SUSPENDED in the end of tpm_pm_suspend() can be racy according, as this leaves window for tpm_hwrng_read() to be called while the operation is in progress. The recent bug report gives also evidence of this behaviour. Aadress this by locking the TPM chip before checking any chip->flags both in tpm_pm_suspend() and tpm_hwrng_read(). Move TPM_CHIP_FLAG_SUSPENDED check inside tpm_get_random() so that it will be always checked only when the lock is reserved. | |||||
| CVE-2024-53053 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix another deadlock during RTC update If ufshcd_rtc_work calls ufshcd_rpm_put_sync() and the pm's usage_count is 0, we will enter the runtime suspend callback. However, the runtime suspend callback will wait to flush ufshcd_rtc_work, causing a deadlock. Replace ufshcd_rpm_put_sync() with ufshcd_rpm_put() to avoid the deadlock. | |||||
| CVE-2024-53052 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 4.4 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/rw: fix missing NOWAIT check for O_DIRECT start write When io_uring starts a write, it'll call kiocb_start_write() to bump the super block rwsem, preventing any freezes from happening while that write is in-flight. The freeze side will grab that rwsem for writing, excluding any new writers from happening and waiting for existing writes to finish. But io_uring unconditionally uses kiocb_start_write(), which will block if someone is currently attempting to freeze the mount point. This causes a deadlock where freeze is waiting for previous writes to complete, but the previous writes cannot complete, as the task that is supposed to complete them is blocked waiting on starting a new write. This results in the following stuck trace showing that dependency with the write blocked starting a new write: task:fio state:D stack:0 pid:886 tgid:886 ppid:876 Call trace: __switch_to+0x1d8/0x348 __schedule+0x8e8/0x2248 schedule+0x110/0x3f0 percpu_rwsem_wait+0x1e8/0x3f8 __percpu_down_read+0xe8/0x500 io_write+0xbb8/0xff8 io_issue_sqe+0x10c/0x1020 io_submit_sqes+0x614/0x2110 __arm64_sys_io_uring_enter+0x524/0x1038 invoke_syscall+0x74/0x268 el0_svc_common.constprop.0+0x160/0x238 do_el0_svc+0x44/0x60 el0_svc+0x44/0xb0 el0t_64_sync_handler+0x118/0x128 el0t_64_sync+0x168/0x170 INFO: task fsfreeze:7364 blocked for more than 15 seconds. Not tainted 6.12.0-rc5-00063-g76aaf945701c #7963 with the attempting freezer stuck trying to grab the rwsem: task:fsfreeze state:D stack:0 pid:7364 tgid:7364 ppid:995 Call trace: __switch_to+0x1d8/0x348 __schedule+0x8e8/0x2248 schedule+0x110/0x3f0 percpu_down_write+0x2b0/0x680 freeze_super+0x248/0x8a8 do_vfs_ioctl+0x149c/0x1b18 __arm64_sys_ioctl+0xd0/0x1a0 invoke_syscall+0x74/0x268 el0_svc_common.constprop.0+0x160/0x238 do_el0_svc+0x44/0x60 el0_svc+0x44/0xb0 el0t_64_sync_handler+0x118/0x128 el0t_64_sync+0x168/0x170 Fix this by having the io_uring side honor IOCB_NOWAIT, and only attempt a blocking grab of the super block rwsem if it isn't set. For normal issue where IOCB_NOWAIT would always be set, this returns -EAGAIN which will have io_uring core issue a blocking attempt of the write. That will in turn also get completions run, ensuring forward progress. Since freezing requires CAP_SYS_ADMIN in the first place, this isn't something that can be triggered by a regular user. | |||||
| CVE-2024-53047 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: mptcp: init: protect sched with rcu_read_lock Enabling CONFIG_PROVE_RCU_LIST with its dependence CONFIG_RCU_EXPERT creates this splat when an MPTCP socket is created: ============================= WARNING: suspicious RCU usage 6.12.0-rc2+ #11 Not tainted ----------------------------- net/mptcp/sched.c:44 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 no locks held by mptcp_connect/176. stack backtrace: CPU: 0 UID: 0 PID: 176 Comm: mptcp_connect Not tainted 6.12.0-rc2+ #11 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:123) lockdep_rcu_suspicious (kernel/locking/lockdep.c:6822) mptcp_sched_find (net/mptcp/sched.c:44 (discriminator 7)) mptcp_init_sock (net/mptcp/protocol.c:2867 (discriminator 1)) ? sock_init_data_uid (arch/x86/include/asm/atomic.h:28) inet_create.part.0.constprop.0 (net/ipv4/af_inet.c:386) ? __sock_create (include/linux/rcupdate.h:347 (discriminator 1)) __sock_create (net/socket.c:1576) __sys_socket (net/socket.c:1671) ? __pfx___sys_socket (net/socket.c:1712) ? do_user_addr_fault (arch/x86/mm/fault.c:1419 (discriminator 1)) __x64_sys_socket (net/socket.c:1728) do_syscall_64 (arch/x86/entry/common.c:52 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) That's because when the socket is initialised, rcu_read_lock() is not used despite the explicit comment written above the declaration of mptcp_sched_find() in sched.c. Adding the missing lock/unlock avoids the warning. | |||||
| CVE-2024-50229 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential deadlock with newly created symlinks Syzbot reported that page_symlink(), called by nilfs_symlink(), triggers memory reclamation involving the filesystem layer, which can result in circular lock dependencies among the reader/writer semaphore nilfs->ns_segctor_sem, s_writers percpu_rwsem (intwrite) and the fs_reclaim pseudo lock. This is because after commit 21fc61c73c39 ("don't put symlink bodies in pagecache into highmem"), the gfp flags of the page cache for symbolic links are overwritten to GFP_KERNEL via inode_nohighmem(). This is not a problem for symlinks read from the backing device, because the __GFP_FS flag is dropped after inode_nohighmem() is called. However, when a new symlink is created with nilfs_symlink(), the gfp flags remain overwritten to GFP_KERNEL. Then, memory allocation called from page_symlink() etc. triggers memory reclamation including the FS layer, which may call nilfs_evict_inode() or nilfs_dirty_inode(). And these can cause a deadlock if they are called while nilfs->ns_segctor_sem is held: Fix this issue by dropping the __GFP_FS flag from the page cache GFP flags of newly created symlinks in the same way that nilfs_new_inode() and __nilfs_read_inode() do, as a workaround until we adopt nofs allocation scope consistently or improve the locking constraints. | |||||
| CVE-2024-49985 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: i2c: stm32f7: Do not prepare/unprepare clock during runtime suspend/resume In case there is any sort of clock controller attached to this I2C bus controller, for example Versaclock or even an AIC32x4 I2C codec, then an I2C transfer triggered from the clock controller clk_ops .prepare callback may trigger a deadlock on drivers/clk/clk.c prepare_lock mutex. This is because the clock controller first grabs the prepare_lock mutex and then performs the prepare operation, including its I2C access. The I2C access resumes this I2C bus controller via .runtime_resume callback, which calls clk_prepare_enable(), which attempts to grab the prepare_lock mutex again and deadlocks. Since the clock are already prepared since probe() and unprepared in remove(), use simple clk_enable()/clk_disable() calls to enable and disable the clock on runtime suspend and resume, to avoid hitting the prepare_lock mutex. | |||||
| CVE-2024-49980 | 1 Linux | 1 Linux Kernel | 2026-06-17 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: vrf: revert "vrf: Remove unnecessary RCU-bh critical section" This reverts commit 504fc6f4f7f681d2a03aa5f68aad549d90eab853. dev_queue_xmit_nit is expected to be called with BH disabled. __dev_queue_xmit has the following: /* Disable soft irqs for various locks below. Also * stops preemption for RCU. */ rcu_read_lock_bh(); VRF must follow this invariant. The referenced commit removed this protection. Which triggered a lockdep warning: ================================ WARNING: inconsistent lock state 6.11.0 #1 Tainted: G W -------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. btserver/134819 [HC0[0]:SC0[0]:HE1:SE1] takes: ffff8882da30c118 (rlock-AF_PACKET){+.?.}-{2:2}, at: tpacket_rcv+0x863/0x3b30 {IN-SOFTIRQ-W} state was registered at: lock_acquire+0x19a/0x4f0 _raw_spin_lock+0x27/0x40 packet_rcv+0xa33/0x1320 __netif_receive_skb_core.constprop.0+0xcb0/0x3a90 __netif_receive_skb_list_core+0x2c9/0x890 netif_receive_skb_list_internal+0x610/0xcc0 [...] other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(rlock-AF_PACKET); <Interrupt> lock(rlock-AF_PACKET); *** DEADLOCK *** Call Trace: <TASK> dump_stack_lvl+0x73/0xa0 mark_lock+0x102e/0x16b0 __lock_acquire+0x9ae/0x6170 lock_acquire+0x19a/0x4f0 _raw_spin_lock+0x27/0x40 tpacket_rcv+0x863/0x3b30 dev_queue_xmit_nit+0x709/0xa40 vrf_finish_direct+0x26e/0x340 [vrf] vrf_l3_out+0x5f4/0xe80 [vrf] __ip_local_out+0x51e/0x7a0 [...] | |||||